rbAmp
ES
Tienda
Docs
Actualizado

16 · Ejemplos de Python en SBC Linux

Este capítulo es el equivalente para SBC de arduino-examples.md, micropython-examples.md, esp-idf-examples.md, stm32-hal-examples.md y pico-sdk-examples.md: los mismos diez escenarios, portados a CPython en Linux (Raspberry Pi OS, Armbian, Linux genérico ARM/x86).

Nota

Estos ejemplos hablan directamente con rbAmp mediante la API de registros I²C en bruto. Están pensados para integraciones de tipo servicio en Linux (pasarelas de Home Assistant, routers OpenWrt, contenedores Docker / k3s, puentes IoT a medida), donde Python es la herramienta adecuada y el acceso directo a registros es válido.

Para una interfaz más cómoda y estructurada, use el paquete Python rbamp (véase la tabla de bibliotecas cliente del README). El paquete encapsula los detalles de registro en una clase RbAmp con métodos con nombre (dev.voltage, dev.latch_period(), dev.read_period_snapshot(), etc.), un acumulador RbAmpEnergy por canal, una variante asyncio mediante async for, auxiliares multimódulo, descubrimiento automático de HA por MQTT y plantillas de servicio systemd en los ejemplos incluidos, y una CLI rbamp (rbamp scan / read --watch / period). El mismo paquete se ejecuta sin cambios en MicroPython; véase la tabla de bibliotecas cliente del README. La mayoría de los proyectos deben partir del paquete y recurrir a la API en bruto solo cuando haga falta.

En qué se diferencia Linux de un microcontrolador

La diferencia principal: Linux ya hace gran parte del trabajo que los ejemplos de bare-metal configuran a mano. No inicializa el periférico I²C, no sincroniza el reloj de pared, no lucha por la memoria retenida entre reinicios. Todo eso existe a nivel de sistema. Su script de Python solo hace medición y lógica de negocio, nada más.

Concretely:

Aspecto MCU bare-metal SBC Linux
Inicialización del periférico I²C i2c_init() / HAL_I2C_Init() Ya lo hace el controlador del kernel (i2c-dev). Abra /dev/i2c-N como descriptor de archivo.
Resistencias pull-up Decídalo en el diseño de la placa o mediante gpio_pull_up() Decidido en hardware. Linux no los toca.
Hora de pared (UTC) Implemente SNTP y llame a gmtime_r() systemd-timesyncd / chrony mantienen el reloj sincronizado automáticamente. time.time() devuelve los segundos reales desde la época.
Persistencia entre reinicios Registros de respaldo del RTC, RAM NOINIT, NVM El sistema de archivos. Use un archivo JSON, SQLite o /var/lib/rbamp/.
Sueño profundo esp_deep_sleep_start() / HAL_PWR_EnterSTANDBYMode() No aplica. El SBC funciona de forma continua; el coste de CPU en reposo lo dominan de todos modos Wi-Fi / Ethernet. La suspensión es un concepto ajeno.
ISR de DRDY IRQ de pin en firmware Eventos de flanco en espacio de usuario mediante gpiod / gpiozero. La latencia es de unos pocos cientos de microsegundos, dominada por la planificación del núcleo.
MQTT Configurar Wi-Fi y escribir a mano una pila TCP/TLS pip install paho-mqtt.
Demonio / supervisor Bucle while infinito Una unidad de servicio systemd, con reinicio automático y registro en journal.
Permisos No aplicable El usuario que ejecute su script debe estar en los grupos i2c y gpio, o ejecutarlo como root.
Sistema de compilación CMake / idf.py / CubeIDE pip install -r requirements.txt (o un pyproject.toml).

Si hasta ahora ha escrito firmware, el cambio mental es este: deje de recurrir a las APIs de bajo nivel. El sistema operativo ya expone todo como archivos o llamadas de la biblioteca estándar.

Configuración I²C en Linux (una vez)

Los pasos siguientes son para Raspberry Pi OS con una Raspberry Pi 3/4/5; otros SBC (Orange Pi, BeagleBone, x86 + adaptador USB-I2C) siguen el mismo patrón con otro número de bus.

1. Active el controlador I²C en el kernel

Raspberry Pi OS: vía sencilla:

Bash
sudo raspi-config nonint do_i2c 0           # 0 = enable

O edite el árbol de dispositivos manualmente:

Bash
sudo nano /boot/firmware/config.txt          # /boot/config.txt on older releases
# Add or uncomment the next line:
dtparam=i2c_arm=on
# Bus speed 100 kHz (recommended) — see also chapter 01:
dtparam=i2c_arm=on,i2c_arm_baudrate=100000

sudo reboot

Tras el reinicio, el kernel expone el bus como un dispositivo de caracteres:

Bash
ls /dev/i2c-*
# -> /dev/i2c-1

En Pi 4/5 también puede habilitar buses adicionales mediante entradas dtoverlay=i2c-bus,bus=N, útil cuando necesita un I²C independiente para rbAmp, separado de los HAT.

Otros SBC:

  • Orange Pi / NanoPi / Banana Pi: opciones similares de dtoverlay o extlinux.conf, según el BSP.
  • BeagleBone Black: config-pin P9.19 i2c / P9.20 i2c para I²C-2; el nodo es /dev/i2c-2.
  • x86 / Linux genérico: un adaptador USB-I2C (FT232H, MCP2221A, CH341) aparece como /dev/i2c-N tras cargar el módulo de kernel adecuado.

2. Instale herramientas de acceso a nivel de núcleo (opcional, pero útil)

Bash
sudo apt update
sudo apt install -y i2c-tools
i2cdetect -y 1                              # scan bus 1

i2cdetect debería mostrar 50 en la dirección por defecto del rbAmp:

Text
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:                         -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
...
50: 50 -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --

3. Permisos de espacio de usuario

Añada su usuario al grupo i2c para no necesitar sudo en cada script:

Bash
sudo usermod -aG i2c $USER
# Log out and back in for the group change to take effect.

Para acceso a DRDY / GPIO:

Bash
sudo usermod -aG gpio $USER                  # Raspberry Pi
sudo usermod -aG dialout $USER               # often required for serial / USB-CDC

Verify:

Bash
groups
# -> ... i2c gpio ...

4. Paquetes de Python

Use un entorno virtual para aislar las dependencias:

Bash
python3 -m venv ~/venv-rbamp
source ~/venv-rbamp/bin/activate

pip install --upgrade pip
pip install smbus2 gpiozero paho-mqtt
# Optional extras used in some examples:
pip install luma.oled            # SSD1306 / SH1106
pip install RPi.GPIO             # alternative to gpiozero on Pi
pip install python-periphery     # cross-SBC I2C / GPIO without smbus2

Para un proyecto publicado use pyproject.toml (PEP 621):

TOML
[project]
name = "my-rbamp-app"
version = "0.1.0"
dependencies = [
    "smbus2>=0.4.0",
    "paho-mqtt>=2.0,<3.0",          # 2.x: callback API version must be passed explicitly
    "gpiozero>=2.0",
]
nota sobre paho-mqtt 2.x

— la versión 2.0 convirtió la versión con API de callbacks en un argumento obligatorio del constructor. Todos los ejemplos de este capítulo pasan mqtt.CallbackAPIVersion.VERSION1 para mantener las firmas simples heredadas (on_connect(client, userdata, flags, rc, properties=None)); si prefiere la v2 (con ReasonCode y ConnectFlags), pase CallbackAPIVersion.VERSION2 y actualice los callbacks en consecuencia.

5. Hora

De forma predeterminada, systemd-timesyncd mantiene el reloj del sistema en UTC sincronizado con NTP. Compruébelo:

Bash
timedatectl
#                Local time: Thu 2026-05-22 18:30:01 CEST
#            Universal time: Thu 2026-05-22 16:30:01 UTC
#  System clock synchronized: yes
#                NTP service: active

En Python llama a time.time() (segundos UTC desde la época), datetime.datetime.now(timezone.utc) o time.localtime(), y ese es el reloj de pared que necesita. No hay código SNTP en su script.

6. Referencia rápida de SBC

SBC nodo I²C Grupo Notas sobre DRDY
Raspberry Pi 3/4/5 /dev/i2c-1 i2c, gpio se recomienda gpiozero
BeagleBone Black /dev/i2c-2 i2c, gpio Adafruit_BBIO / libgpiod
Orange Pi 4/5 /dev/i2c-3 (varía) i2c, gpio OPi.GPIO o libgpiod
x86 genérico + USB-I2C /dev/i2c-3..N i2c DRDY a través del GPIO del adaptador (FT232H lo admite)

El resto de este capítulo supone Raspberry Pi 4 / 5 + Raspberry Pi OS, pero todos los ejemplos funcionan en cualquier SBC con el número de bus y la biblioteca de GPIO correspondientes.


Índice de ejemplos

# Título Dificultad Salida MQTT DRDY Multimódulo Bidireccional Caso de uso
1 Lectura rápida mínimo Consola — — — — Prueba de humo
2 Medidor de energía de 60 segundos en OLED bajo SSD1306 — — — — Contador Wh encapsulado
3 Monitor multimódulo bajo Consola — — sí (3) — Monitorización de toda la vivienda
4 Medidor de energía por aparato (UI3) medio — sí — — — Submedición en HA
5 Bidireccional en el maestro con un módulo BASIC medio Consola — sí — sí (maestro) Vivienda solar en nivel BASIC
6 Balance energético de la vivienda alta — sí — sí (3) sí Balance energético de la vivienda
7 Detección de eventos de corriente medio Registro en archivo — sí — — Registro de eventos de electrodomésticos
8 Publicador MQTT con auto-descubrimiento de HA medio — sí (+disco) — — opcional Integración de HA lista para usar
9 Demonio systemd con persistencia en SQLite medio journald + BD sí — — — Registrador de producción
10 Tarifa por franjas horarias (TOU) con reloj del sistema medio Consola sí — — opcional Medición por tarifa punta / valle

Auxiliares comunes (rbamp_io.py)

Coloque este archivo junto a sus scripts (o impórtelo desde un paquete). Para ahorrar espacio, no se repite en los ejemplos siguientes.

Python
"""rbAmp raw-I2C helpers for Linux CPython.

Uses smbus2 — the most widely available userspace I2C library on Linux.
For older systems, ``python3-smbus`` (the official Linux i2c-tools binding)
exposes a nearly identical API.

For cross-SBC portability without smbus2, swap in python-periphery; the
helpers are thin enough to port in a few minutes.
"""
from __future__ import annotations

import struct
import time
from typing import Optional

from smbus2 import SMBus, i2c_msg


# ---------- rbAmp register addresses (subset used in the examples) ----------
REG_STATUS         = 0x00
REG_COMMAND        = 0x01
REG_VERSION        = 0x03
REG_CT_MODEL       = 0x05
REG_PERIOD_VALID   = 0x07
REG_AC_FREQ        = 0x20
REG_I2C_ADDRESS    = 0x30
REG_U_RMS          = 0x86
REG_U_PEAK         = 0x8A
REG_I0_RMS         = 0x8E
REG_I1_RMS         = 0x92
REG_I2_RMS         = 0x96
REG_P0_REAL        = 0xA6
REG_PF0            = 0xB2
REG_Q0             = 0xD0
REG_PERIOD_AVG_P1  = 0xC2
REG_PERIOD_AVG_P2  = 0xC6
REG_DATA_VALID     = 0xCE
REG_PERIOD_AVG_P0  = 0xDC
REG_PERIOD_MAX_P   = 0xE0
REG_PERIOD_LATCH_MS= 0xEC

CMD_RESET          = 0x01
CMD_LATCH_PERIOD   = 0x27


class RbAmpIO:
    """Thin wrapper around an SMBus / address pair.

    Holds the bus handle and the target slave address, exposing one helper
    per primitive operation. Designed to be composed into larger classes
    (or used directly in scripts).
    """

    def __init__(self, bus: SMBus, addr: int = 0x50) -> None:
        """Bind to an already-opened SMBus and a 7-bit address.

        :param bus: An ``smbus2.SMBus(N)`` instance.
        :param addr: 7-bit slave address (default 0x50).
        """
        self.bus = bus
        self.addr = addr

    # ----- I2C primitives -----

    def read_u8(self, reg: int) -> int:
        """Read one byte from a register."""
        return self.bus.read_byte_data(self.addr, reg)

    def write_u8(self, reg: int, val: int) -> None:
        """Write one byte to a register."""
        self.bus.write_byte_data(self.addr, reg, val & 0xFF)

    def read_float_le(self, reg: int) -> float:
        """Read a little-endian float32 from four consecutive registers.

        rbAmp supports READ auto-increment (a single burst-read is valid for
        atomicity). The per-byte form below is shown for clarity. WRITE
        transactions, by contrast, are byte-at-a-time only. See chapter 11.
        """
        b = bytes(self.read_u8(reg + i) for i in range(4))
        return struct.unpack(" int:
        """Read a little-endian uint32 from four consecutive registers."""
        b = bytes(self.read_u8(reg + i) for i in range(4))
        return struct.unpack(" bool:
        """Return True if the slave acks a single-byte read of REG_STATUS."""
        try:
            self.bus.read_byte_data(self.addr, REG_STATUS)
            return True
        except OSError:
            return False

    def wait_ready(self, timeout_s: float = 2.0) -> None:
        """Block until DATA_VALID bit 0 reads 1, or raise TimeoutError."""
        deadline = time.monotonic() + timeout_s
        while time.monotonic() < deadline:
            try:
                if self.read_u8(REG_DATA_VALID) & 0x01:
                    return
            except OSError:
                pass
            time.sleep(0.05)
        raise TimeoutError(f"rbAmp at 0x{self.addr:02X} not ready in {timeout_s}s")


def broadcast_latch(bus: SMBus, tick16: int, group: int = 0) -> bool:
    """Broadcast CMD_LATCH_PERIOD to rbAmp modules with GC reception enabled.

    Canonical 5-byte general-call frame: A5 27 group tick_lo tick_hi.
    Slaves reject any first byte != 0xA5. GC reception is opt-in per
    module (FLEET_CONFIG.bit0, default OFF). See chapter 11 §6.3.2.

    Returns True on ACK; False on NACK (caller must fall back to
    per-module sequential snapshot).
    """
    msg = i2c_msg.write(0x00, [
        0xA5,                            # frame magic
        CMD_LATCH_PERIOD,                # opcode 0x27
        group & 0xFF,                    # group_id (0 = all-call)
        tick16 & 0xFF,                   # tick_lo
        (tick16 >> 8) & 0xFF,            # tick_hi
    ])
    try:
        bus.i2c_rdwr(msg)
        return True
    except OSError:
        return False

Ejemplo 1: lectura rápida (mínimo)

Objetivo: mostrar U, I, P, PF en la consola una vez por segundo. Hardware: cualquier SBC + un rbAmp UI1 en /dev/i2c-1.

example_01.py:

Python
#!/usr/bin/env python3
"""rbAmp quick-read smoke test."""
import time
from smbus2 import SMBus
from rbamp_io import RbAmpIO, REG_VERSION, REG_U_RMS, REG_I0_RMS, REG_P0_REAL, REG_PF0

I2C_BUS = 1
RB_ADDR = 0x50

with SMBus(I2C_BUS) as bus:
    meter = RbAmpIO(bus, RB_ADDR)
    meter.wait_ready()                              # wait for first RT window
    print(f"rbAmp version: 0x{meter.read_u8(REG_VERSION):02X}")

    while True:
        u  = meter.read_float_le(REG_U_RMS)         # RMS voltage,  V
        i_ = meter.read_float_le(REG_I0_RMS)        # RMS current,  A
        p  = meter.read_float_le(REG_P0_REAL)       # active power, W (signed)
        pf = meter.read_float_le(REG_PF0)           # power factor, signed
        print(f"U={u:.1f}V  I={i_:.3f}A  P={p:+.1f}W  PF={pf:+.3f}")
        time.sleep(1)

Run:

Bash
python3 example_01.py
# rbAmp version: 0x04
# U=230.1V  I=0.262A  P=+60.2W  PF=+0.998
# U=229.9V  I=0.262A  P=+60.1W  PF=+0.998
# ...

Si ve PermissionError: [Errno 13] en /dev/i2c-1, su usuario no está en el grupo i2c: corríjalo según la sección de configuración de Linux anterior.


Ejemplo 2: medidor de energía de 60 segundos en OLED

Objetivo: contador de Wh actualizado una vez por minuto, mostrado en un SSD1306 de 128×64 que comparte el bus I²C del rbAmp. Hardware: SBC + rbAmp + OLED SSD1306 (0x3C) en el mismo bus. Contabilidad: unidireccional (nivel BASIC). Biblioteca: luma.oled para la pantalla (pip install luma.oled).

Python
#!/usr/bin/env python3
"""60-second energy meter on a 128x64 SSD1306, shared I2C bus."""
import time
from smbus2 import SMBus
from luma.core.interface.serial import i2c as luma_i2c
from luma.oled.device import ssd1306
from luma.core.render import canvas

from rbamp_io import (
    RbAmpIO, REG_COMMAND, REG_PERIOD_VALID,
    REG_PERIOD_AVG_P0, CMD_LATCH_PERIOD,
)

I2C_BUS = 1
RB_ADDR = 0x50

# luma opens its own connection but still drives /dev/i2c-1 — coexists with smbus2.
serial = luma_i2c(port=I2C_BUS, address=0x3C)
oled = ssd1306(serial, width=128, height=64)


def draw(avg_p: float, dt_s: float, total_wh: float) -> None:
    """Render the three lines."""
    with canvas(oled) as c:
        c.text((0, 0),  f"P:  {avg_p:6.1f} W", fill="white")
        c.text((0, 16), f"dt: {dt_s:6.1f} s",  fill="white")
        c.text((0, 32), f"{total_wh:.2f} Wh",  fill="white")


with SMBus(I2C_BUS) as bus:
    meter = RbAmpIO(bus, RB_ADDR)
    meter.wait_ready()

    # Primer snapshot — discard its snapshot.
    meter.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)
    t_prev = time.monotonic()
    total_wh = 0.0

    while True:
        time.sleep(60)

        # 1) Final snapshot — closes the period [t_prev .. now].
        meter.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)
        t_now = time.monotonic()
        time.sleep(0.05)                              # let firmware finalise snapshot

        # 2) Verify the snapshot is fresh.
        if (meter.read_u8(REG_PERIOD_VALID) & 0x01) == 0:
            print("WARN: stale snapshot")
            t_prev = time.monotonic()
            continue

        # 3) Read time-averaged power, channel 0.
        avg_p = meter.read_float_le(REG_PERIOD_AVG_P0)

        # 4) Energy uses the MASTER clock — same idea as on a microcontroller,
        # except `time.monotonic()` is the Linux equivalent of `HAL_GetTick()`.
        dt_s = t_now - t_prev
        e_wh = avg_p * dt_s / 3600.0
        total_wh += e_wh
        t_prev = t_now

        draw(avg_p, dt_s, total_wh)
        print(f"avg_P={avg_p:.1f}  E_period={e_wh:.3f}  total={total_wh:.3f}")

Ejemplo 3: monitor multimódulo

Objetivo: sondear tres módulos (alimentación principal, calentador de agua, AC) e imprimir la potencia total. Hardware: SBC + 3 × rbAmp UI1 en 0x50, 0x51 y 0x52.

Python
#!/usr/bin/env python3
"""Round-robin polling of three rbAmp modules."""
import time
from smbus2 import SMBus
from rbamp_io import RbAmpIO, REG_U_RMS, REG_P0_REAL

I2C_BUS = 1
MODULES = [
    (0x50, "Mains "),
    (0x51, "Boiler"),
    (0x52, "AC    "),
]

with SMBus(I2C_BUS) as bus:
    meters = [(RbAmpIO(bus, addr), label) for addr, label in MODULES]

    # Probe every module before entering the read loop.
    for meter, label in meters:
        if not meter.probe():
            raise SystemExit(f"{label} at 0x{meter.addr:02X} not found")
    print("All modules OK")

    while True:
        total_p = 0.0
        print("---")
        for meter, label in meters:
            u = meter.read_float_le(REG_U_RMS)
            p = meter.read_float_le(REG_P0_REAL)
            print(f"[{label}] U={u:.1f}  P={p:+.1f} W")
            total_p += p
        print(f"TOTAL: {total_p:.1f} W")
        time.sleep(2)

probe() llama a una lectura de 1 byte read_byte_data y captura OSError(EREMOTEIO): el equivalente en Linux de un NACK de I²C.


Ejemplo 4: medidor de energía por aparato (UI3)

Objetivo: un módulo UI3 con tres pinzas de corriente CT en tres cargas distintas de la misma fase; contadores Wh independientes publicados por MQTT cada minuto. Hardware: SBC + 1 × rbAmp UI3 + broker MQTT (Mosquitto, EMQX, complemento Mosquitto de HA).

Python
#!/usr/bin/env python3
"""Per-appliance UI3 energy tracker with MQTT publishing."""
import json
import time

import paho.mqtt.client as mqtt
from smbus2 import SMBus

from rbamp_io import (
    RbAmpIO, REG_COMMAND, REG_PERIOD_VALID,
    REG_PERIOD_AVG_P0, REG_PERIOD_AVG_P1, REG_PERIOD_AVG_P2,
    CMD_LATCH_PERIOD,
)

I2C_BUS    = 1
RB_ADDR    = 0x50
CH_NAMES   = ("main", "heatpump", "lights")
MQTT_HOST  = "192.168.1.10"

client = mqtt.Client(mqtt.CallbackAPIVersion.VERSION1, client_id="rbamp-ui3")
try:
    client.connect(MQTT_HOST, 1883, keepalive=60)
except OSError as e:
    print(f"MQTT broker unreachable at boot ({e}); will retry in loop_start()")
client.loop_start()                            # paho's thread reconnects automatically


def mqtt_publish(name: str, avg_p: float, e_wh: float) -> None:
    """Publish one channel's state to MQTT."""
    payload = json.dumps({"power": round(avg_p, 1), "energy": round(e_wh, 4)})
    client.publish(f"rbamp/{name}/state", payload, qos=0, retain=False)


with SMBus(I2C_BUS) as bus:
    meter = RbAmpIO(bus, RB_ADDR)
    meter.wait_ready()

    meter.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)        # primer
    t_prev = time.monotonic()
    total_wh = [0.0, 0.0, 0.0]

    while True:
        time.sleep(60)

        meter.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)
        t_now = time.monotonic()
        time.sleep(0.05)

        if (meter.read_u8(REG_PERIOD_VALID) & 0x01) == 0:
            t_prev = time.monotonic()
            continue

        # PERIOD_AVG_P_W per channel: I0 at 0xDC, I1 at 0xC2, I2 at 0xC6.
        avg_p = (
            meter.read_float_le(REG_PERIOD_AVG_P0),
            meter.read_float_le(REG_PERIOD_AVG_P1),
            meter.read_float_le(REG_PERIOD_AVG_P2),
        )
        dt_s = t_now - t_prev
        t_prev = t_now

        for ch in range(3):
            e = avg_p[ch] * dt_s / 3600.0
            total_wh[ch] += e
            print(f"[{CH_NAMES[ch]}] avg_P={avg_p[ch]:+.1f} W  E_total={total_wh[ch]:.3f} Wh")
            mqtt_publish(CH_NAMES[ch], avg_p[ch], total_wh[ch])

Ejemplo 5: bidireccional en el maestro con un módulo BASIC

Objetivo: implementar contabilidad bidireccional en el maestro mientras el módulo tiene firmware BASIC. El SBC reacciona al flanco de bajada de DRDY mediante gpiozero y separa consumo y exportación. Hardware: Raspberry Pi + rbAmp UI1; DRDY conectado al GPIO 15 (numeración BCM).

Python
#!/usr/bin/env python3
"""Master-side bidirectional accounting via DRDY GPIO IRQ."""
import time
from threading import Event

from gpiozero import Button
from smbus2 import SMBus

from rbamp_io import RbAmpIO, REG_P0_REAL

I2C_BUS  = 1
RB_ADDR  = 0x50
PIN_DRDY = 15                  # BCM

# Wrap the bus in a context manager so the /dev/i2c-N fd is released cleanly
# on any unhandled exception (Ctrl-C, NACK retry exhaustion, etc.).
with SMBus(I2C_BUS) as bus:
    meter  = RbAmpIO(bus, RB_ADDR)
    meter.wait_ready()

    # gpiozero treats DRDY as a "Button":
    #   pull_up=True -> the line idles HIGH (matches rbAmp's open-drain output)
    #   bounce_time=None — we want the raw falling edges, not debounced
    drdy = Button(PIN_DRDY, pull_up=True, bounce_time=None)
    data_ready = Event()

    def on_drdy() -> None:
        """gpiozero callback — only sets the flag. All I/O happens in the main loop."""
        data_ready.set()

    drdy.when_pressed = on_drdy

    e_consumed_wh = 0.0
    e_exported_wh = 0.0
    t_last = time.monotonic()
    t_last_print = t_last
    print("Bidirectional accumulator started")

    while True:
        if not data_ready.wait(timeout=1.0):
            continue                                # no edge in the last second
        data_ready.clear()

        t_now = time.monotonic()
        p = meter.read_float_le(REG_P0_REAL)        # signed P_real
        dt_s = t_now - t_last
        t_last = t_now

        if p > 0:
            e_consumed_wh += p * dt_s / 3600.0
        else:
            e_exported_wh += -p * dt_s / 3600.0

        # Summary print every 5 s.
        if t_now - t_last_print >= 5.0:
            t_last_print = t_now
            print(f"P={p:+8.1f}W   consumed={e_consumed_wh:.4f} Wh  "
                  f"exported={e_exported_wh:.4f} Wh  "
                  f"net={(e_consumed_wh - e_exported_wh):+.4f} Wh")

Notes:

  • threading.Event es la primitiva de sincronización natural: set() desde el callback, wait() desde el bucle principal. La latencia de planificación de Linux es muy inferior a la cadencia de la ventana RT de ~100 ms, así que no se pierde ningún flanco.
  • En versiones antiguas de Pi OS sin gpiozero, sustituya por RPi.GPIO.add_event_detect(15, GPIO.FALLING, callback=on_drdy). En SBC que no son Pi, use gpiod.LineRequest (libgpiod 2.x); el resto del script no cambia.

Ejemplo 6: balance energético del hogar

Objetivo: panel de balance energético completo. Tres módulos:

  • rbAmp n.º 1 en la alimentación principal (STD: bidireccional)
  • rbAmp n.º 2 en la salida del inversor solar (BASIC válido)
  • rbAmp n.º 3, UI3, en tres cargas grandes (calefacción, AC, VE)

El maestro usa broadcast_latch() para instantáneas síncronas y publica un saldo retenido por MQTT cada minuto.

Python
#!/usr/bin/env python3
"""Home energy balance via synchronous broadcast snapshot."""
import json
import time

import paho.mqtt.client as mqtt
from smbus2 import SMBus

from rbamp_io import (
    RbAmpIO, broadcast_latch,
    REG_PERIOD_VALID, REG_PERIOD_AVG_P0, REG_PERIOD_AVG_P1, REG_PERIOD_AVG_P2,
)

I2C_BUS    = 1
ADDR_MAINS = 0x50                # bidirectional (STD)
ADDR_SOLAR = 0x51                # generation only (BASIC ok)
ADDR_LOADS = 0x52                # UI3
MQTT_HOST  = "192.168.1.10"

# PERIOD_AVG_P_NEG register for the mains module — see the SKU datasheet
# of the STD product. Set to None on BASIC modules.
from typing import Optional
REG_PERIOD_AVG_P_NEG_MAINS: Optional[int] = None     # Optional[int] for Py 3.9+ compat

client = mqtt.Client(mqtt.CallbackAPIVersion.VERSION1, client_id="home-balance")
try:
    client.connect(MQTT_HOST, 1883, keepalive=60)
except OSError as e:
    print(f"MQTT broker unreachable at boot ({e}); will retry in loop_start()")
client.loop_start()


def safe_read_float(meter: RbAmpIO, reg: int) -> float:
    """Return 0.0 if the read fails (e.g. NACK from a BASIC module)."""
    try:
        return meter.read_float_le(reg)
    except OSError:
        return 0.0


totals = {
    "mains_in_wh":    0.0,
    "mains_out_wh":   0.0,
    "solar_total_wh": 0.0,
    "loads_wh":       [0.0, 0.0, 0.0],
}

with SMBus(I2C_BUS) as bus:
    mains = RbAmpIO(bus, ADDR_MAINS)
    solar = RbAmpIO(bus, ADDR_SOLAR)
    loads = RbAmpIO(bus, ADDR_LOADS)
    for m in (mains, solar, loads):
        m.wait_ready()

    gc_tick = 0
    if not broadcast_latch(bus, gc_tick):
        # GC NACK → fall back to per-module sequential snapshot.
        for m in (mains, solar, loads):
            m.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)
    gc_tick += 1
    t_prev = time.monotonic()
    print("Home balance started")

    while True:
        time.sleep(60)

        # Synchronous snapshot — all modules snapshot at the same instant.
        if not broadcast_latch(bus, gc_tick):
            for m in (mains, solar, loads):
                m.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)
        gc_tick = (gc_tick + 1) & 0xFFFF
        t_now = time.monotonic()
        time.sleep(0.05)
        dt_s = t_now - t_prev
        t_prev = t_now

        # ---- MAINS (bidirectional) ----
        if mains.read_u8(REG_PERIOD_VALID) & 0x01:
            p_consume = safe_read_float(mains, REG_PERIOD_AVG_P0)
            p_export  = (safe_read_float(mains, REG_PERIOD_AVG_P_NEG_MAINS)
                         if REG_PERIOD_AVG_P_NEG_MAINS is not None else 0.0)
            totals["mains_in_wh"]  += p_consume * dt_s / 3600.0
            totals["mains_out_wh"] += p_export  * dt_s / 3600.0

        # ---- SOLAR ----
        if solar.read_u8(REG_PERIOD_VALID) & 0x01:
            p = safe_read_float(solar, REG_PERIOD_AVG_P0)
            totals["solar_total_wh"] += p * dt_s / 3600.0

        # ---- LOADS (UI3) ----
        if loads.read_u8(REG_PERIOD_VALID) & 0x01:
            for i, reg in enumerate((REG_PERIOD_AVG_P0, REG_PERIOD_AVG_P1, REG_PERIOD_AVG_P2)):
                p = safe_read_float(loads, reg)
                totals["loads_wh"][i] += p * dt_s / 3600.0

        # Derived balance figures.
        total_consumed  = (totals["mains_in_wh"]
                           + totals["solar_total_wh"]
                           - totals["mains_out_wh"])
        solar_self_used = max(0.0, totals["solar_total_wh"] - totals["mains_out_wh"])

        print(f"MAINS  in={totals['mains_in_wh']:.2f}  out={totals['mains_out_wh']:.2f}")
        print(f"SOLAR  gen={totals['solar_total_wh']:.2f}  "
              f"self-used={solar_self_used:.2f}  exported={totals['mains_out_wh']:.2f}")
        print(f"LOADS  HP={totals['loads_wh'][0]:.2f}  "
              f"AC={totals['loads_wh'][1]:.2f}  EV={totals['loads_wh'][2]:.2f}")
        print(f"TOTAL  household consumed={total_consumed:.2f} Wh")

        payload = json.dumps({
            "mains_in":       round(totals["mains_in_wh"], 3),
            "mains_out":      round(totals["mains_out_wh"], 3),
            "solar":          round(totals["solar_total_wh"], 3),
            "self_used":      round(solar_self_used, 3),
            "total_consumed": round(total_consumed, 3),
            "hp":             round(totals["loads_wh"][0], 3),
            "ac":             round(totals["loads_wh"][1], 3),
            "ev":             round(totals["loads_wh"][2], 3),
        })
        client.publish("home/energy/balance", payload, qos=1, retain=True)

Ejemplo 7: detección de eventos de corriente

Objetivo: en cada flanco de DRDY, comparar la P instantánea con una EMA y añadir las desviaciones significativas a un archivo de registro rotatorio. Hardware: cualquier SBC + rbAmp + DRDY conectado al GPIO 15. Registro: el módulo estándar logging de Python con RotatingFileHandler; sobrevive a los reinicios y no requiere controlador de tarjeta SD.

Python
#!/usr/bin/env python3
"""Power-event detection with rotating-file logging."""
import logging
import logging.handlers
import time
from threading import Event

from gpiozero import Button
from smbus2 import SMBus

from rbamp_io import RbAmpIO, REG_P0_REAL

I2C_BUS  = 1
RB_ADDR  = 0x50
PIN_DRDY = 15

EMA_ALPHA = 0.05
EVENT_THRESHOLD_W = 200.0
LOG_PATH = "/var/log/rbamp/events.log"   # ensure the directory exists and is writeable

# Configure a rotating logger — 5 files × 1 MB.
handler = logging.handlers.RotatingFileHandler(
    LOG_PATH, maxBytes=1_000_000, backupCount=5)
handler.setFormatter(logging.Formatter("%(asctime)s  %(message)s",
                                       "%Y-%m-%dT%H:%M:%S"))
log = logging.getLogger("rbamp.events")
log.addHandler(handler)
log.setLevel(logging.INFO)

# Wrap the bus in a context manager so the /dev/i2c-N fd is released cleanly
# on any unhandled exception.
with SMBus(I2C_BUS) as bus:
    meter = RbAmpIO(bus, RB_ADDR)
    meter.wait_ready()

    # Seed the EMA with current power so the very first sample does not look like an event.
    p_ema = meter.read_float_le(REG_P0_REAL)

    drdy = Button(PIN_DRDY, pull_up=True, bounce_time=None)
    data_ready = Event()
    drdy.when_pressed = data_ready.set

    print("Event detector started; log:", LOG_PATH)

    while True:
        if not data_ready.wait(timeout=1.0):
            continue
        data_ready.clear()

        p = meter.read_float_le(REG_P0_REAL)
        delta = p - p_ema
        p_ema = (1 - EMA_ALPHA) * p_ema + EMA_ALPHA * p

        if abs(delta) > EVENT_THRESHOLD_W:
            event_type = "TURN_ON" if delta > 0 else "TURN_OFF"
            line = f"{event_type}  delta={delta:+.1f}W  P={p:.1f}W  EMA={p_ema:.1f}W"
            print(line)
            log.info(line)                          # MUST be inside the `if` —
                                                    # otherwise NameError when
                                                    # delta is below threshold.
Nota

El directorio debe existir con los permisos adecuados:

Bash
sudo mkdir -p /var/log/rbamp && sudo chown $USER /var/log/rbamp
O escriba en~/.local/state/rbamp/events.logsi no quiere usar rutas gestionadas por root.


Ejemplo 8: publicador MQTT con descubrimiento automático de Home Assistant

Objetivo: integración directa con HA. El SBC publica configuraciones de auto-descubrimiento de HA (retenidas) y emite un estado en JSON cada minuto. Hardware: cualquier SBC + un rbAmp UI1 + broker MQTT.

Python
#!/usr/bin/env python3
"""rbAmp MQTT publisher with Home Assistant Auto-discovery."""
import json
import time

import paho.mqtt.client as mqtt
from smbus2 import SMBus

from rbamp_io import (
    RbAmpIO,
    REG_COMMAND, REG_PERIOD_VALID, REG_PERIOD_AVG_P0,
    REG_U_RMS, REG_I0_RMS, REG_PF0, REG_Q0, REG_AC_FREQ,
    CMD_LATCH_PERIOD,
)

I2C_BUS     = 1
RB_ADDR     = 0x50
DEVICE_ID   = "rbamp_main"
DEVICE_NAME = "Mains rbAmp"
MQTT_HOST   = "192.168.1.10"
MQTT_USER   = None     # set to a string to enable basic auth
MQTT_PASS   = None

DEVICE_BLOCK = {
    "identifiers":  [DEVICE_ID],
    "name":         DEVICE_NAME,
    "manufacturer": "rbAmp",
    "model":        "rbAmp UI*",
}


def publish_discovery_sensor(client: mqtt.Client, key: str, friendly: str,
                             unit: str | None, dev_class: str | None,
                             state_class: str) -> None:
    """Publish one HA discovery config (retained)."""
    cfg = {
        "name":            f"{DEVICE_NAME} {friendly}",
        "unique_id":       f"{DEVICE_ID}_{key}",
        "state_topic":     f"rbamp/{DEVICE_ID}/state",
        "value_template":  "{{ value_json." + key + " }}",
        "state_class":     state_class,
        "device":          DEVICE_BLOCK,
    }
    if unit:      cfg["unit_of_measurement"] = unit
    if dev_class: cfg["device_class"] = dev_class
    client.publish(f"homeassistant/sensor/{DEVICE_ID}/{key}/config",
                   json.dumps(cfg), qos=1, retain=True)


def publish_discovery_all(client: mqtt.Client) -> None:
    """Publish the full HA discovery set for one rbAmp module."""
    publish_discovery_sensor(client, "voltage",        "Voltage",        "V",   "voltage",        "measurement")
    publish_discovery_sensor(client, "current",        "Current",        "A",   "current",        "measurement")
    publish_discovery_sensor(client, "power",          "Power",          "W",   "power",          "measurement")
    publish_discovery_sensor(client, "energy",         "Energy",         "Wh",  "energy",         "total_increasing")
    publish_discovery_sensor(client, "frequency",      "Frequency",      "Hz",  "frequency",      "measurement")
    publish_discovery_sensor(client, "power_factor",   "Power Factor",   None,  "power_factor",   "measurement")
    publish_discovery_sensor(client, "apparent_power", "Apparent Power", "VA",  "apparent_power", "measurement")
    publish_discovery_sensor(client, "reactive_power", "Reactive Power", "var", "reactive_power", "measurement")


def on_connect(client, userdata, flags, rc, properties=None):
    """Republish discovery on every (re)connect — retained, so HA picks it up."""
    print(f"MQTT connected rc={rc}")
    publish_discovery_all(client)


client = mqtt.Client(mqtt.CallbackAPIVersion.VERSION1,
                     client_id=DEVICE_ID, protocol=mqtt.MQTTv5)
if MQTT_USER:
    client.username_pw_set(MQTT_USER, MQTT_PASS)
client.on_connect = on_connect
try:
    client.connect(MQTT_HOST, 1883, keepalive=60)
except OSError as e:
    print(f"MQTT broker unreachable at boot ({e}); will retry in loop_start()")
client.loop_start()

with SMBus(I2C_BUS) as bus:
    meter = RbAmpIO(bus, RB_ADDR)
    meter.wait_ready()

    meter.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)        # primer
    t_prev = time.monotonic()
    total_wh = 0.0

    while True:
        time.sleep(60)

        meter.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)
        t_now = time.monotonic()
        time.sleep(0.05)

        if (meter.read_u8(REG_PERIOD_VALID) & 0x01) == 0:
            t_prev = time.monotonic()
            continue

        avg_p = meter.read_float_le(REG_PERIOD_AVG_P0)
        dt_s  = t_now - t_prev
        total_wh += avg_p * dt_s / 3600.0
        t_prev = t_now

        # Live RT values for the state payload.
        u  = meter.read_float_le(REG_U_RMS)
        i_ = meter.read_float_le(REG_I0_RMS)
        pf = meter.read_float_le(REG_PF0)
        q  = meter.read_float_le(REG_Q0)
        freq = meter.read_u8(REG_AC_FREQ)

        payload = json.dumps({
            "voltage":        round(u, 1),
            "current":        round(i_, 3),
            "power":          round(avg_p, 1),
            "energy":         round(total_wh, 3),
            "frequency":      int(freq),
            "power_factor":   round(pf, 3),
            "apparent_power": round(u * i_, 1),
            "reactive_power": round(q, 1),
        })
        client.publish(f"rbamp/{DEVICE_ID}/state", payload, qos=0, retain=False)
        print(f"Published: {payload}")

Tras la primera publicación, Home Assistant crea automáticamente un dispositivo Mains rbAmp con ocho sensores, incluida una entidad Energy que encaja directamente en el panel de energía.


Ejemplo 9: demonio systemd con persistencia SQLite

Nota

Este ejemplo sustituye el «registrador de sueño profundo alimentado por batería» de los capítulos de microcontroladores. En Linux el SBC funciona de forma continua, así que el patrón adecuado es un demonio gestionado por systemd con reinicio automático ante fallos y una pequeña base de datos SQLite para la persistencia entre cortes de alimentación.

Objetivo: un demonio de larga ejecución que toma una instantánea del periodo cada minuto, escribe el resultado en SQLite y publica un estado por MQTT. El proceso se reinicia limpiamente tras un reinicio, recuperando el total acumulado de la base de datos. Hardware: cualquier SBC + un rbAmp UI1.

Demonio (rbamp_daemon.py)

Python
#!/usr/bin/env python3
"""rbAmp daemon — periodic snapshot + SQLite persistence + MQTT."""
import json
import logging
import signal
import sqlite3
import sys
import time
from contextlib import closing

import paho.mqtt.client as mqtt
from smbus2 import SMBus

from rbamp_io import (
    RbAmpIO, REG_COMMAND, REG_PERIOD_VALID,
    REG_PERIOD_AVG_P0, CMD_LATCH_PERIOD,
)

# ----- Configuration -----
I2C_BUS    = 1
RB_ADDR    = 0x50
DB_PATH    = "/var/lib/rbamp/energy.db"
MQTT_HOST  = "192.168.1.10"
PERIOD_S   = 60

# ----- Logging -----
logging.basicConfig(
    level=logging.INFO,
    format="%(asctime)s  %(levelname)s  %(message)s",
    stream=sys.stdout,                          # systemd captures stdout into the journal
)
log = logging.getLogger("rbamp.daemon")


# ----- SQLite persistence -----

def db_init(conn: sqlite3.Connection) -> None:
    """Create the schema if it does not exist."""
    conn.executescript("""
        CREATE TABLE IF NOT EXISTS energy_state (
            id          INTEGER PRIMARY KEY CHECK (id = 1),
            total_wh    REAL NOT NULL DEFAULT 0
        );
        INSERT OR IGNORE INTO energy_state(id, total_wh) VALUES (1, 0);

        CREATE TABLE IF NOT EXISTS energy_log (
            ts          INTEGER NOT NULL,
            dt_s        REAL    NOT NULL,
            avg_p_w     REAL    NOT NULL,
            e_wh        REAL    NOT NULL,
            total_wh    REAL    NOT NULL
        );
        CREATE INDEX IF NOT EXISTS idx_energy_log_ts ON energy_log(ts);
    """)
    conn.commit()


def db_load_total(conn: sqlite3.Connection) -> float:
    """Return the accumulated total_wh persisted across restarts."""
    row = conn.execute("SELECT total_wh FROM energy_state WHERE id = 1").fetchone()
    return float(row[0]) if row else 0.0


def db_record(conn: sqlite3.Connection, dt_s: float, avg_p: float,
              e_wh: float, total: float) -> None:
    """Append one period sample and update the running total atomically."""
    with conn:                                  # implicit BEGIN/COMMIT
        conn.execute("UPDATE energy_state SET total_wh = ? WHERE id = 1", (total,))
        conn.execute(
            "INSERT INTO energy_log(ts, dt_s, avg_p_w, e_wh, total_wh) "
            "VALUES (?, ?, ?, ?, ?)",
            (int(time.time()), dt_s, avg_p, e_wh, total),
        )


# ----- Signal handling for clean shutdown -----

_running = True

def _shutdown(signum, frame):
    """Handle SIGTERM (systemd stop) / SIGINT (Ctrl-C) gracefully."""
    global _running
    log.info("Shutdown signal %d received", signum)
    _running = False

signal.signal(signal.SIGTERM, _shutdown)
signal.signal(signal.SIGINT,  _shutdown)


# ----- Main -----

def main() -> int:
    client = mqtt.Client(mqtt.CallbackAPIVersion.VERSION1, client_id="rbamp-daemon")
    try:
        client.connect(MQTT_HOST, 1883, keepalive=60)
    except OSError as e:
        log.warning("MQTT broker unreachable at boot (%s); paho will retry", e)
    client.loop_start()                        # paho's thread reconnects automatically

    with SMBus(I2C_BUS) as bus, closing(sqlite3.connect(DB_PATH)) as conn:
        db_init(conn)
        total_wh = db_load_total(conn)
        log.info("Resumed total_wh = %.3f Wh", total_wh)

        meter = RbAmpIO(bus, RB_ADDR)
        meter.wait_ready()

        meter.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)    # primer
        t_prev = time.monotonic()

        while _running:
            # Sleep in 1-second slices so we can respond to SIGTERM quickly.
            for _ in range(PERIOD_S):
                if not _running:
                    break
                time.sleep(1)
            if not _running:
                break

            meter.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)
            t_now = time.monotonic()
            time.sleep(0.05)

            if (meter.read_u8(REG_PERIOD_VALID) & 0x01) == 0:
                log.warning("Stale snapshot — skipping")
                t_prev = time.monotonic()
                continue

            avg_p = meter.read_float_le(REG_PERIOD_AVG_P0)
            dt_s  = t_now - t_prev
            e_wh  = avg_p * dt_s / 3600.0
            total_wh += e_wh
            t_prev = t_now

            db_record(conn, dt_s, avg_p, e_wh, total_wh)
            client.publish("rbamp/daemon/state",
                           json.dumps({
                               "dt_s": round(dt_s, 1),
                               "avg_p": round(avg_p, 1),
                               "energy_wh": round(total_wh, 3),
                           }),
                           qos=1, retain=True)
            log.info("avg_P=%+.1f W  E_period=%.3f Wh  total=%.3f Wh",
                     avg_p, e_wh, total_wh)

    log.info("Daemon stopped cleanly; total_wh = %.3f Wh", total_wh)
    client.loop_stop()
    client.disconnect()
    return 0


if __name__ == "__main__":
    sys.exit(main())

unidad systemd (/etc/systemd/system/rbamp.service)

INI
[Unit]
Description=rbAmp energy daemon
After=network-online.target time-sync.target
Wants=network-online.target time-sync.target

[Service]
Type=simple
ExecStart=/home/pi/venv-rbamp/bin/python /opt/rbamp/rbamp_daemon.py
User=pi
Group=i2c
Restart=on-failure
RestartSec=5
# Pre-create the persistence directory so the daemon never sees ENOENT.
RuntimeDirectoryMode=0755
StateDirectory=rbamp
StateDirectoryMode=0755

[Install]
WantedBy=multi-user.target

Habilitar e iniciar:

Bash
sudo systemctl daemon-reload
sudo systemctl enable --now rbamp.service
journalctl -fu rbamp.service                    # follow the log

El demonio:

  • Se reinicia ante fallos (Restart=on-failure).
  • Arranca después de la red y de la sincronización del reloj (After=network-online.target time-sync.target).
  • Sobrevive a los reinicios; la base de datos SQLite en /var/lib/rbamp/energy.db conserva el total acumulado.
  • Responde a systemctl stop rbamp capturando SIGTERM y escribiendo un registro de estado final.

Es el equivalente en SBC de «suspensión profunda + memoria RTC retenida»: en lugar de ahorrar µA, dependemos del sistema operativo para mantenernos despiertos y de un RTC con respaldo de batería para mantener la hora.


Ejemplo 10: tarifa por franjas horarias (TOU) con reloj del sistema

Objetivo: facturar la energía según un horario de tarifa por franjas horarias. El SBC usa el reloj del sistema (ya sincronizado por systemd-timesyncd), así que no hace falta código SNTP. Hardware: cualquier SBC + un rbAmp UI1.

Python
#!/usr/bin/env python3
"""TOU tariff metering using the Linux system clock."""
import json
import time
from datetime import datetime, timezone
from zoneinfo import ZoneInfo               # stdlib since Python 3.9

import paho.mqtt.client as mqtt
from smbus2 import SMBus

from rbamp_io import (
    RbAmpIO, REG_COMMAND, REG_PERIOD_VALID, REG_PERIOD_AVG_P0,
    CMD_LATCH_PERIOD,
)

I2C_BUS   = 1
RB_ADDR   = 0x50
MQTT_HOST = "192.168.1.10"

# IANA timezone name — Python's stdlib handles DST automatically.
TZ = ZoneInfo("Europe/Berlin")
PEAK_START_HOUR = 8        # inclusive
PEAK_END_HOUR   = 22       # exclusive


def is_peak_hour(hour: int) -> bool:
    """Return True if `hour` (local) falls inside the peak window.

    For schedules that span midnight (peak = 22..6), change to
    ``return hour >= PEAK_START_HOUR or hour < PEAK_END_HOUR``.
    """
    return PEAK_START_HOUR <= hour < PEAK_END_HOUR


client = mqtt.Client(mqtt.CallbackAPIVersion.VERSION1, client_id="rbamp-tou")
try:
    client.connect(MQTT_HOST, 1883, keepalive=60)
except OSError as e:
    print(f"MQTT broker unreachable at boot ({e}); will retry in loop_start()")
client.loop_start()

# Tariff buckets.
today = {"peak_wh": 0.0, "off_peak_wh": 0.0, "yday": -1}
lifetime = {"peak_wh": 0.0, "off_peak_wh": 0.0}


def accumulate(e_wh: float, now_local: datetime) -> None:
    """Add this period's energy to the right bucket and roll the day at midnight."""
    yday = now_local.timetuple().tm_yday
    if today["yday"] != yday:
        if today["yday"] >= 0:
            payload = json.dumps({
                "yday":        today["yday"],
                "peak_wh":     round(today["peak_wh"], 3),
                "off_peak_wh": round(today["off_peak_wh"], 3),
                "total_wh":    round(today["peak_wh"] + today["off_peak_wh"], 3),
            })
            client.publish("rbamp/tou/day_close", payload, qos=1, retain=True)
            print("Day closed:", payload)
        today["peak_wh"] = 0.0
        today["off_peak_wh"] = 0.0
        today["yday"] = yday

    if is_peak_hour(now_local.hour):
        today["peak_wh"]    += e_wh
        lifetime["peak_wh"] += e_wh
    else:
        today["off_peak_wh"]    += e_wh
        lifetime["off_peak_wh"] += e_wh


with SMBus(I2C_BUS) as bus:
    meter = RbAmpIO(bus, RB_ADDR)
    meter.wait_ready()
    meter.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)        # primer
    t_prev = time.monotonic()
    print(f"TOU started: peak {PEAK_START_HOUR:02d}:00..{PEAK_END_HOUR:02d}:00 local")

    while True:
        time.sleep(60)

        meter.write_u8(REG_COMMAND, CMD_LATCH_PERIOD)
        t_now = time.monotonic()
        time.sleep(0.05)

        if (meter.read_u8(REG_PERIOD_VALID) & 0x01) == 0:
            t_prev = time.monotonic()
            continue

        avg_p = meter.read_float_le(REG_PERIOD_AVG_P0)
        dt_s  = t_now - t_prev
        e_wh  = avg_p * dt_s / 3600.0
        t_prev = t_now

        # The Linux system clock is already authoritative — no SNTP code required.
        now_local = datetime.now(TZ)
        accumulate(e_wh, now_local)
        peak = is_peak_hour(now_local.hour)

        payload = json.dumps({
            "ts":                now_local.isoformat(timespec="seconds"),
            "tariff":            "peak" if peak else "off_peak",
            "avg_p":             round(avg_p, 1),
            "period_wh":         round(e_wh, 4),
            "today_peak_wh":     round(today["peak_wh"], 3),
            "today_off_peak_wh": round(today["off_peak_wh"], 3),
            "life_peak_wh":      round(lifetime["peak_wh"], 3),
            "life_off_peak_wh":  round(lifetime["off_peak_wh"], 3),
        })
        client.publish("rbamp/tou/state", payload, qos=0, retain=False)
        print(payload)

Notes:

  • zoneinfo es la API moderna de zonas horarias de la biblioteca estándar de Python 3.9+. En Debian / Raspberry Pi OS toma los datos IANA del paquete tzdata del sistema; las transiciones de horario de verano se gestionan correctamente.
  • Para Python 3.8 o anteriores, sustituya pytz: import pytz; TZ = pytz.timezone("Europe/Berlin").
  • Las marcas de tiempo ISO 8601 con desfase las produce datetime.isoformat(timespec="seconds"); por ejemplo, 2026-05-22T18:30:00+02:00.
  • Para la medición bidireccional de un STD, llame a accumulate() dos veces: una para el consumo y otra para la exportación, y publique ambos cubos punta / valle.

Comparación de ejemplos

# Complejidad Salida MQTT DRDY Multimódulo Bidireccional Persistencia Caso de uso
1 mínimo Consola — — — — — prueba de humo
2 bajo OLED — — — — RAM medidor en caja
3 bajo Consola — — sí (3) — — monitorización doméstica
4 medio — sí — — — RAM por electrodoméstico en HA
5 medio Consola — sí — sí (maestro) RAM vivienda solar en nivel BASIC
6 alta — sí — sí (3) sí RAM + MQTT (retenido) balance energético de toda la casa
7 medio Archivo de registro rotatorio — sí — — sistema de archivos detección de eventos
8 medio — sí (+disco) — — opcional RAM + MQTT Auto-descubrimiento de HA
9 medio journald + SQLite sí — — — SQLite demonio de producción
10 medio Consola sí — — opcional RAM + MQTT (cierre diario) TOU punta/fuera de punta

Buenas prácticas

  • Ejecute los scripts como usuario sin privilegios, en los grupos i2c y gpio. Evite sudo python ...: contamina las rutas y rompe las instalaciones con pip --user.
  • Use un entorno virtual (python3 -m venv ...) en lugar de instalar paquetes con sudo pip en todo el sistema.
  • Capture siempre OSError alrededor de las lecturas I²C: un NACK transitorio o un esclavo desconectado temporalmente aparece como OSError(EREMOTEIO). El código de producción reintenta; el código de prueba de humo deja que falle para que el fallo sea visible.
  • Use time.monotonic() para el reloj maestro. No le afecta que systemd-timesyncd ajuste a saltos el reloj de pared (p. ej. en la primera sincronización tras el arranque). Use time.time() / datetime solo para marcas de tiempo.
  • PERIOD_VALID (0x07) debe comprobarse tras cada CMD_LATCH_PERIOD. La misma regla que en un microcontrolador: Linux no cambia el protocolo de rbAmp.
  • Espere ≥ 50 ms tras una instantánea (time.sleep(0.05)) antes de leer 0xDC..0xEF.
  • Para configuraciones con varios módulos, broadcast_latch(bus, tick) mediante llamada general ofrece una sincronización precisa. La recepción GC es opcional por módulo (FLEET_CONFIG.bit0, por defecto desactivada). Si hay NACK, recurra a CMD_LATCH_PERIOD secuencial por módulo.
  • Guarde los totales en el sistema de archivos: JSON, SQLite, InfluxDB. El sistema de archivos es el equivalente en SBC de los «registros de respaldo del RTC + NVM». Es barato y fiable.
  • Envuelva el bucle principal con manejadores de señales (SIGTERM, SIGINT) para que systemctl stop detenga el demonio limpiamente con una escritura final de estado.
  • Escriba en stdout/stderr en los demonios: journald lo captura automáticamente; obtiene rotación, filtrado y journalctl -u rbamp sin esfuerzo.

Lo siguiente

Tras repasar estos diez ejemplos: