rbAmp
ES
Tienda
Docs
Actualizado

15 · Ejemplos de Raspberry Pi Pico SDK

Este capítulo es el equivalente para Raspberry Pi Pico de arduino-examples.md, micropython-examples.md, esp-idf-examples.md y stm32-hal-examples.md: los mismos diez escenarios, portados a C nativo con Pico SDK (pico-sdk 1.5+ / 2.x) y red basada en LwIP.

Nota

Estos ejemplos hablan con rbAmp directamente mediante la API de registros I²C sin procesar. Están pensados para firmware embebido de producción en RP2040 / RP2350: control directo del Cortex-M0+ / M33 de doble núcleo, integración con el cliente MQTT de LwIP, FATFS y las primitivas de suspensión y persistencia del SDK.

No se incluye ninguna biblioteca dedicada de Pico SDK: las bibliotecas cliente cubren Arduino (incl. arduino-pico para RP2040 mediante la API Wire), MicroPython (funciona en el puerto RP2040), ESP-IDF y CPython en SBC Linux; vea la tabla de bibliotecas cliente del README. Para firmware nativo de Pico SDK en C, siga las recetas de API sin procesar de abajo. Si quiere una API de más alto nivel en RP2040, lo más fácil es el núcleo arduino-pico + la biblioteca Arduino de rbAmp.

Objetivos compatibles y cadena de herramientas

Destino Validado Wi-Fi Notas
Raspberry Pi Pico (RP2040) ✓ no Ejemplos 1–3, 5, 7 solo con I²C
Raspberry Pi Pico W (RP2040 + CYW43) ✓ sí Todos los ejemplos; usa pico-cyw43-arch + LwIP
Raspberry Pi Pico 2 (RP2350) ✓ no Cortex-M33
Raspberry Pi Pico 2 W (RP2350 + CYW43) ✓ sí Todos los ejemplos

Cadena de herramientas: pico-sdk 1.5.1+ (o 2.x para RP2350), CMake 3.13+, arm-none-eabi-gcc 12+; se recomienda la extensión oficial «Raspberry Pi Pico» para VS Code.

Estructura del proyecto

Cada ejemplo usa la estructura estándar de proyecto pico-sdk:

Text
example_NN/
├── CMakeLists.txt
├── pico_sdk_import.cmake
└── src/
    ├── example_NN.c
    ├── rbamp_io.h
    ├── rbamp_io.c
    └── lwipopts.h         (only for Wi-Fi examples)

CMakeLists.txt de nivel superior:

CMake
cmake_minimum_required(VERSION 3.13)

# Pull in the SDK before project() — see pico-sdk template.
include(pico_sdk_import.cmake)

# For Pico W, set BOARD before project():
# set(PICO_BOARD pico_w)

project(example_NN C CXX ASM)
set(CMAKE_C_STANDARD 11)
pico_sdk_init()

add_executable(example_NN
    src/example_NN.c
    src/rbamp_io.c)

target_include_directories(example_NN PRIVATE src)

# Always-required libraries.
target_link_libraries(example_NN
    pico_stdlib
    hardware_i2c)

# Wi-Fi examples add CYW43 + LwIP + mqtt:
# target_link_libraries(example_NN
#     pico_cyw43_arch_lwip_threadsafe_background
#     pico_lwip_mqtt
#     pico_lwip_sntp)
# target_compile_definitions(example_NN PRIVATE WIFI_SSID=\"...\" WIFI_PASSWORD=\"...\")

# Route stdio to USB CDC (for Pico's serial console).
pico_enable_stdio_usb(example_NN 1)
pico_enable_stdio_uart(example_NN 0)

pico_add_extra_outputs(example_NN)

Compilar y cargar:

Bash
mkdir build && cd build
cmake ..
make -j
# Drag-and-drop the .uf2 onto the RPI-RP2 / RP2350 USB mass-storage device.

Índice de ejemplos

# Título Dificultad Salida MQTT DRDY Multimódulo Bidireccional Caso de uso
1 Lectura rápida mínimo stdio USB — — — — Prueba de humo
2 Medidor de energía de 60 segundos en OLED bajo SSD1306 — — — — Contador Wh encapsulado
3 Monitor multimódulo bajo stdio USB — — sí (3) — Monitorización de toda la vivienda
4 Medidor de energía por aparato (UI3) medio — sí — — — Submedición en HA
5 Bidireccional en el maestro con un módulo BASIC medio stdio USB — sí — sí (maestro) Vivienda solar en nivel BASIC
6 Balance energético de la vivienda alta — sí — sí (3) sí Balance energético de la vivienda
7 Detección de eventos de corriente medio USB + SD — sí — — Registro de eventos de electrodomésticos
8 Publicador MQTT con auto-descubrimiento de HA medio — sí (+disco) — — opcional Integración de HA lista para usar
9 Registrador alimentado por batería con reposo latente medio — sí — — — Medidor exterior / autónomo
10 Tarifa por franjas horarias (TOU) con hora de pared SNTP medio stdio USB sí — — opcional Medición por tarifa punta / valle
Nota

Los ejemplos con Wi-Fi (4, 6, 8, 9, 10) requieren Pico W o Pico 2 W.


Auxiliares comunes (rbamp_io.h / rbamp_io.c)

Coloque estos archivos en el directorio src/ de su proyecto. Para ahorrar espacio, la línea #include "rbamp_io.h" se omite en cada ejemplo.

rbamp_io.h

C
/**
 * @file rbamp_io.h
 * @brief Raw I2C helpers for the rbAmp slave (Raspberry Pi Pico SDK).
 */
#pragma once

#include 
#include 
#include "pico/stdlib.h"
#include "hardware/i2c.h"

#ifdef __cplusplus
extern "C" {
#endif

#define RBAMP_I2C_TIMEOUT_US  50000U     /* 50 ms */

/**
 * @brief  Initialise the I2C peripheral and pin functions.
 * @param  i2c_inst   i2c0 or i2c1.
 * @param  sda_gpio   SDA GPIO number (e.g. 4 for default i2c0).
 * @param  scl_gpio   SCL GPIO number (e.g. 5 for default i2c0).
 * @param  baudrate   Bus speed (use 50000 — the recommended 50 kHz; wrap reads in a short retry, see ch. 11 §2.2).
 */
void rbamp_io_init(i2c_inst_t *i2c_inst, uint sda_gpio, uint scl_gpio,
                   uint baudrate);

/**
 * @brief  Read one byte from a register of an rbAmp slave.
 * @return PICO_OK on success, an error code otherwise.
 */
int rbamp_io_read_u8(uint8_t addr, uint8_t reg, uint8_t *out);

/**
 * @brief  Read a little-endian float32 from four consecutive registers.
 * @details Reads four consecutive bytes. rbAmp supports READ auto-increment
 *          (a single burst-read is valid for atomicity). The per-byte form
 *          is shown for clarity. See chapter 11 for asymmetry rules.
 */
int rbamp_io_read_float_le(uint8_t addr, uint8_t reg, float *out);

/**
 * @brief  Read a little-endian uint32 from four consecutive registers.
 */
int rbamp_io_read_u32_le(uint8_t addr, uint8_t reg, uint32_t *out);

/**
 * @brief  Write a single byte to a register.
 */
int rbamp_io_write_u8(uint8_t addr, uint8_t reg, uint8_t val);

/**
 * @brief  Broadcast CMD_LATCH_PERIOD to every rbAmp with GC reception
 *         enabled (FLEET_CONFIG.bit0 = 1; opt-in, default OFF).
 * @details Canonical 5-byte general-call frame: A5 27 group tick_lo tick_hi.
 *          Slaves reject any first byte != 0xA5. See chapter 11 §6.3.2.
 * @param  tick16  Caller's 16-bit window counter (mirrored at GC_TICK 0x59).
 * @param  group   GROUP_ID filter (0 = all-call).
 * @return PICO_OK on ACK; PICO_ERROR_GENERIC on NACK — fall back to per-module.
 */
int rbamp_io_broadcast_latch(uint16_t tick16, uint8_t group);

/**
 * @brief  Probe whether a slave responds at the given address.
 * @return true if the slave acks, false otherwise.
 */
bool rbamp_io_probe(uint8_t addr);

/**
 * @brief  Block until DATA_VALID bit 0 of register 0xCE reads 1, or timeout.
 * @return PICO_OK on success, PICO_ERROR_TIMEOUT otherwise.
 */
int rbamp_io_wait_ready(uint8_t addr, uint32_t timeout_ms);

/* ===== rbAmp register addresses (subset used in examples) ===== */
#define RB_REG_STATUS           0x00U
#define RB_REG_COMMAND          0x01U
#define RB_REG_VERSION          0x03U
#define RB_REG_AC_FREQ          0x20U
#define RB_REG_PERIOD_VALID     0x07U
#define RB_REG_U_RMS            0x86U
#define RB_REG_I0_RMS           0x8EU
#define RB_REG_I1_RMS           0x92U
#define RB_REG_I2_RMS           0x96U
#define RB_REG_P0_REAL          0xA6U
#define RB_REG_PF0              0xB2U
#define RB_REG_Q0               0xD0U
#define RB_REG_DATA_VALID       0xCEU
#define RB_REG_PERIOD_AVG_P0    0xDCU
#define RB_REG_PERIOD_AVG_P1    0xC2U
#define RB_REG_PERIOD_AVG_P2    0xC6U
#define RB_REG_PERIOD_MAX_P     0xE0U
#define RB_REG_PERIOD_LATCH_MS  0xECU

/* ===== Commands ===== */
#define RB_CMD_RESET            0x01U
#define RB_CMD_LATCH_PERIOD     0x27U

#ifdef __cplusplus
}
#endif

rbamp_io.c

C
#include "rbamp_io.h"
#include 
#include "pico/error.h"

static i2c_inst_t *s_i2c = NULL;

void rbamp_io_init(i2c_inst_t *i2c_inst, uint sda_gpio, uint scl_gpio,
                   uint baudrate) {
    s_i2c = i2c_inst;
    i2c_init(s_i2c, baudrate);
    gpio_set_function(sda_gpio, GPIO_FUNC_I2C);
    gpio_set_function(scl_gpio, GPIO_FUNC_I2C);
    /* The rbAmp board carries its own pull-ups; do NOT enable the internal
     * pulls unless yours are physically removed. */
}

/**
 * @brief  Internal helper — one register read.
 * @details Pattern: write reg-address (nostop=true) + read 1 byte.
 */
static int read_one(uint8_t addr, uint8_t reg, uint8_t *out) {
    int n = i2c_write_timeout_us(s_i2c, addr, ®, 1,
                                  /*nostop=*/true, RBAMP_I2C_TIMEOUT_US);
    if (n != 1) return PICO_ERROR_GENERIC;
    n = i2c_read_timeout_us(s_i2c, addr, out, 1,
                             /*nostop=*/false, RBAMP_I2C_TIMEOUT_US);
    return (n == 1) ? PICO_OK : PICO_ERROR_GENERIC;
}

int rbamp_io_read_u8(uint8_t addr, uint8_t reg, uint8_t *out) {
    return read_one(addr, reg, out);
}

int rbamp_io_read_float_le(uint8_t addr, uint8_t reg, float *out) {
    uint8_t buf[4];
    for (int i = 0; i < 4; i++) {
        int rc = read_one(addr, (uint8_t)(reg + i), &buf[i]);
        if (rc != PICO_OK) return rc;
    }
    memcpy(out, buf, sizeof(float));   /* RP2040 / RP2350 are little-endian */
    return PICO_OK;
}

int rbamp_io_read_u32_le(uint8_t addr, uint8_t reg, uint32_t *out) {
    uint8_t buf[4];
    for (int i = 0; i < 4; i++) {
        int rc = read_one(addr, (uint8_t)(reg + i), &buf[i]);
        if (rc != PICO_OK) return rc;
    }
    *out = (uint32_t)buf[0] | (uint32_t)buf[1] << 8
         | (uint32_t)buf[2] << 16 | (uint32_t)buf[3] << 24;
    return PICO_OK;
}

int rbamp_io_write_u8(uint8_t addr, uint8_t reg, uint8_t val) {
    uint8_t tx[2] = { reg, val };
    int n = i2c_write_timeout_us(s_i2c, addr, tx, 2,
                                  /*nostop=*/false, RBAMP_I2C_TIMEOUT_US);
    return (n == 2) ? PICO_OK : PICO_ERROR_GENERIC;
}

int rbamp_io_broadcast_latch(uint16_t tick16, uint8_t group) {
    /* Canonical 5-byte general-call frame: A5 27 group tick_lo tick_hi. */
    uint8_t tx[5] = {
        0xA5,                          /* frame magic */
        RB_CMD_LATCH_PERIOD,           /* opcode 0x27 */
        group,                         /* group_id (0 = all-call) */
        (uint8_t)(tick16 & 0xFF),
        (uint8_t)((tick16 >> 8) & 0xFF),
    };
    int n = i2c_write_timeout_us(s_i2c, /*addr=*/0x00U, tx, sizeof tx,
                                  /*nostop=*/false, RBAMP_I2C_TIMEOUT_US);
    return (n == (int)sizeof tx) ? PICO_OK : PICO_ERROR_GENERIC;
}

bool rbamp_io_probe(uint8_t addr) {
    uint8_t dummy;
    /* A 1-byte read is the simplest ACK probe — read the STATUS register. */
    return read_one(addr, RB_REG_STATUS, &dummy) == PICO_OK;
}

int rbamp_io_wait_ready(uint8_t addr, uint32_t timeout_ms) {
    absolute_time_t deadline = make_timeout_time_ms(timeout_ms);
    while (!time_reached(deadline)) {
        uint8_t v = 0;
        if (rbamp_io_read_u8(addr, RB_REG_DATA_VALID, &v) == PICO_OK
            && (v & 0x01U)) {
            return PICO_OK;
        }
        sleep_ms(50);
    }
    return PICO_ERROR_TIMEOUT;
}

Ejemplo 1: lectura rápida (mínimo)

Objetivo: imprimir U, I, P, PF por USB CDC una vez por segundo. Hardware: Raspberry Pi Pico + un rbAmp UI1. I²C en GPIO 4 (SDA) / GPIO 5 (SCL): pines predeterminados de i2c0.

src/example_01.c:

C
#include 
#include "pico/stdlib.h"
#include "hardware/i2c.h"
#include "rbamp_io.h"

#define RB_ADDR  0x50U

int main(void) {
    stdio_init_all();                       /* USB CDC stdio */
    sleep_ms(2000);                         /* let the USB host enumerate */

    /* I2C0 on GPIO 4 / 5 at the recommended 50 kHz. */
    rbamp_io_init(i2c0, 4, 5, 50000);

    /* Wait until the first RT window has been computed. */
    if (rbamp_io_wait_ready(RB_ADDR, 2000) != PICO_OK) {
        printf("ERROR: rbAmp not ready\n");
        while (1) tight_loop_contents();
    }

    uint8_t ver = 0;
    rbamp_io_read_u8(RB_ADDR, RB_REG_VERSION, &ver);
    printf("rbAmp version: 0x%02X\n", ver);

    while (true) {
        float u, i_, p, pf;
        rbamp_io_read_float_le(RB_ADDR, RB_REG_U_RMS,   &u );
        rbamp_io_read_float_le(RB_ADDR, RB_REG_I0_RMS,  &i_);
        rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p );
        rbamp_io_read_float_le(RB_ADDR, RB_REG_PF0,     &pf);
        printf("U=%.1fV  I=%.3fA  P=%+.1fW  PF=%+.3f\n", u, i_, p, pf);
        sleep_ms(1000);
    }
}

Salida esperada en la consola serie:

Text
rbAmp version: 0x04
U=230.1V  I=0.262A  P=+60.2W  PF=+0.998
U=229.9V  I=0.262A  P=+60.1W  PF=+0.998
...
Nota

Conéctese a la consola serie con minicom -D /dev/ttyACM0 -b 115200 (Linux), screen /dev/cu.usbmodem* (macOS) o PuTTY (Windows).


Ejemplo 2: medidor de energía de 60 segundos en OLED

Objetivo: contador Wh actualizado una vez por minuto, mostrado en un SSD1306 de 128×64 que comparte el bus I²C de rbAmp. Hardware: Pico + rbAmp + SSD1306 (0x3C) en el mismo bus. Biblioteca: un controlador SSD1306 estándar del Pico SDK (p. ej. daschr/pico-ssd1306). La API de la OLED que sigue es simbólica: sustitúyala por las llamadas de su controlador.

C
#include 
#include 
#include "pico/stdlib.h"
#include "rbamp_io.h"
#include "ssd1306.h"

#define RB_ADDR  0x50U

int main(void) {
    stdio_init_all();
    sleep_ms(2000);
    rbamp_io_init(i2c0, 4, 5, 50000);

    /* OLED shares the same i2c0. */
    ssd1306_t oled;
    ssd1306_init(&oled, 128, 64, 0x3C, i2c0);

    rbamp_io_wait_ready(RB_ADDR, 2000);

    /* Primer snapshot — discard its snapshot. */
    rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
    uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
    double total_wh = 0.0;

    while (true) {
        sleep_ms(60 * 1000);

        /* 1) Final snapshot. */
        rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
        uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
        sleep_ms(50);                       /* let firmware finalise snapshot */

        /* 2) Check PERIOD_VALID. */
        uint8_t valid = 0;
        rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
        if ((valid & 0x01U) == 0) {
            printf("WARN: stale snapshot\n");
            t_prev_ms = to_ms_since_boot(get_absolute_time());
            continue;
        }

        /* 3) Read time-averaged P. */
        float avg_p = 0.0f;
        rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);

        /* 4) Energy uses the MASTER clock. */
        float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
        double e_wh = (double)avg_p * dt_s / 3600.0;
        total_wh += e_wh;
        t_prev_ms = t_now_ms;

        /* 5) Render. */
        char line[32];
        ssd1306_clear(&oled);
        snprintf(line, sizeof(line), "P:  %6.1f W", avg_p);
        ssd1306_draw_string(&oled, 0, 0,  1, line);
        snprintf(line, sizeof(line), "dt: %6.1f s", dt_s);
        ssd1306_draw_string(&oled, 0, 16, 1, line);
        snprintf(line, sizeof(line), "%.2f Wh", total_wh);
        ssd1306_draw_string(&oled, 0, 32, 2, line);
        ssd1306_show(&oled);

        printf("avg_P=%.1f  E_period=%.3f  total=%.3f\n", avg_p, e_wh, total_wh);
    }
}
Nota

La OLED y rbAmp comparten i2c0: nunca llame a i2c_init() dos veces; la función rbamp_io_init() ya lo hizo.


Ejemplo 3: monitor multimódulo

Objetivo: sondear tres módulos (alimentación principal, calentador de agua, AC) e imprimir el total. Hardware: Pico + 3 × rbAmp UI1 en 0x50, 0x51 y 0x52.

C
#include 
#include 
#include "pico/stdlib.h"
#include "rbamp_io.h"

typedef struct {
    uint8_t addr;
    const char *label;
} module_t;

static const module_t modules[] = {
    { 0x50, "Mains " },
    { 0x51, "Boiler" },
    { 0x52, "AC    " },
};
#define N_MODULES (sizeof(modules) / sizeof(modules[0]))

int main(void) {
    stdio_init_all();
    sleep_ms(2000);
    rbamp_io_init(i2c0, 4, 5, 50000);

    /* Probe every module before entering the read loop. */
    for (size_t i = 0; i < N_MODULES; i++) {
        if (!rbamp_io_probe(modules[i].addr)) {
            printf("ERROR: %s at 0x%02X not found\n",
                   modules[i].label, modules[i].addr);
            while (1) tight_loop_contents();
        }
    }
    printf("All modules OK\n");

    while (true) {
        float total_p = 0.0f;
        printf("---\n");

        /* Round-robin read. */
        for (size_t i = 0; i < N_MODULES; i++) {
            float u = 0.0f, p = 0.0f;
            rbamp_io_read_float_le(modules[i].addr, RB_REG_U_RMS,   &u);
            rbamp_io_read_float_le(modules[i].addr, RB_REG_P0_REAL, &p);
            printf("[%s] U=%.1f  P=%+.1f W\n", modules[i].label, u, p);
            total_p += p;
        }
        printf("TOTAL: %.1f W\n", total_p);
        sleep_ms(2000);
    }
}

Ejemplo 4: medidor de energía por aparato (UI3)

Objetivo: un módulo UI3 con tres pinzas de corriente CT en tres cargas distintas de la misma fase; contadores Wh independientes publicados por MQTT cada minuto. Hardware: Pico W (o Pico 2 W) + 1 × rbAmp UI3 + red Wi-Fi con un broker MQTT. Componentes del SDK: pico_cyw43_arch_lwip_threadsafe_background, pico_lwip_mqtt.

Adiciones a CMakeLists.txt:

CMake
set(PICO_BOARD pico_w)

target_link_libraries(example_04
    pico_stdlib
    hardware_i2c
    pico_cyw43_arch_lwip_threadsafe_background
    pico_lwip_mqtt)

target_compile_definitions(example_04 PRIVATE
    WIFI_SSID=\"ssid\"
    WIFI_PASSWORD=\"password\"
    MQTT_BROKER_IP=\"192.168.1.10\")

src/lwipopts.h (mínimo: amplíelo desde pico-examples/pico_w/wifi/lwipopts_examples_common.h):

C
#pragma once
#include "lwip/apps/mqtt.h"
#define LWIP_MQTT 1
#define MEMP_NUM_SYS_TIMEOUT 8
/* Use the SDK's standard threadsafe-background opts. */

src/example_04.c:

C
#include 
#include 
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "lwip/dns.h"
#include "rbamp_io.h"

#define RB_ADDR 0x50U
static const char *CH_NAMES[3] = { "main", "heatpump", "lights" };

static mqtt_client_t *s_mqtt;
static ip_addr_t s_broker_ip;

/**
 * @brief  MQTT connection-status callback (logs result; could trigger retry).
 */
static void mqtt_conn_cb(mqtt_client_t *client, void *arg,
                         mqtt_connection_status_t status) {
    printf("MQTT connect status=%d\n", (int)status);
}

/**
 * @brief  Bring up Wi-Fi (CYW43) and connect to the MQTT broker.
 */
static void net_init(void) {
    if (cyw43_arch_init()) {
        printf("CYW43 init failed\n");
        return;
    }
    cyw43_arch_enable_sta_mode();
    if (cyw43_arch_wifi_connect_timeout_ms(WIFI_SSID, WIFI_PASSWORD,
                                            CYW43_AUTH_WPA2_AES_PSK, 30000)) {
        printf("Wi-Fi connect failed\n");
        return;
    }
    printf("Wi-Fi up\n");

    ipaddr_aton(MQTT_BROKER_IP, &s_broker_ip);
    s_mqtt = mqtt_client_new();
    struct mqtt_connect_client_info_t ci = { .client_id = "rbamp-ui3" };
    mqtt_client_connect(s_mqtt, &s_broker_ip, 1883, mqtt_conn_cb, NULL, &ci);
}

/**
 * @brief  Publish one channel's state to MQTT.
 */
static void mqtt_publish_channel(const char *ch_name, float avg_p, double e_wh) {
    char topic[64], payload[64];
    snprintf(topic,   sizeof(topic),   "rbamp/%s/state", ch_name);
    int n = snprintf(payload, sizeof(payload),
                     "{\"power\":%.1f,\"energy\":%.4f}", avg_p, e_wh);
    mqtt_publish(s_mqtt, topic, payload, n, /*qos*/ 0, /*retain*/ 0,
                 NULL, NULL);
}

int main(void) {
    stdio_init_all();
    sleep_ms(2000);
    net_init();
    rbamp_io_init(i2c0, 4, 5, 50000);
    rbamp_io_wait_ready(RB_ADDR, 2000);

    rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);  /* primer */
    uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
    double total_wh[3] = { 0.0, 0.0, 0.0 };

    while (true) {
        sleep_ms(60 * 1000);

        rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
        uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
        sleep_ms(50);

        uint8_t valid = 0;
        rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
        if ((valid & 0x01U) == 0) {
            t_prev_ms = to_ms_since_boot(get_absolute_time());
            continue;
        }

        /* PERIOD_AVG_P_W per channel: I0 at 0xDC, I1 at 0xC2, I2 at 0xC6. */
        float avg_p[3];
        rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p[0]);
        rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P1, &avg_p[1]);
        rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P2, &avg_p[2]);

        float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
        t_prev_ms = t_now_ms;

        for (int ch = 0; ch < 3; ch++) {
            double e = (double)avg_p[ch] * dt_s / 3600.0;
            total_wh[ch] += e;
            printf("[%s] avg_P=%+.1f W  E_total=%.3f Wh\n",
                   CH_NAMES[ch], avg_p[ch], total_wh[ch]);
            mqtt_publish_channel(CH_NAMES[ch], avg_p[ch], total_wh[ch]);
        }
    }
}

Ejemplo 5: bidireccional en el maestro con un módulo BASIC

Objetivo: implementar contabilidad bidireccional en el maestro mientras el módulo tiene firmware BASIC. La Pico reacciona al flanco de bajada de DRDY mediante una IRQ de GPIO y separa el consumo y la exportación. Hardware: Pico + rbAmp UI1; DRDY conectado al GPIO 15.

C
#include 
#include 
#include "pico/stdlib.h"
#include "pico/critical_section.h"
#include "hardware/gpio.h"
#include "rbamp_io.h"

#define RB_ADDR    0x50U
#define PIN_DRDY   15

static volatile bool g_data_ready = false;

/**
 * @brief  Shared GPIO IRQ callback for the Pico SDK.
 * @details The SDK uses a single callback for all GPIO IRQs — we filter by pin.
 *          Keep the callback short (no I2C, no printf inside an IRQ).
 */
static void gpio_callback(uint gpio, uint32_t events) {
    if (gpio == PIN_DRDY && (events & GPIO_IRQ_EDGE_FALL)) {
        g_data_ready = true;
    }
}

int main(void) {
    stdio_init_all();
    sleep_ms(2000);
    rbamp_io_init(i2c0, 4, 5, 50000);
    rbamp_io_wait_ready(RB_ADDR, 2000);

    /* DRDY input with internal pull-up; falling-edge IRQ. */
    gpio_init(PIN_DRDY);
    gpio_set_dir(PIN_DRDY, GPIO_IN);
    gpio_pull_up(PIN_DRDY);
    gpio_set_irq_enabled_with_callback(PIN_DRDY, GPIO_IRQ_EDGE_FALL,
                                        true, &gpio_callback);

    double e_consumed_wh = 0.0;
    double e_exported_wh = 0.0;
    // Use uint64_t for microsecond counters — to_us_since_boot() returns u64;
    // truncating to u32 overflows every ~71.6 minutes and produces a multi-kWh
    // dt_s spike on the wrap.
    uint64_t t_last_us = to_us_since_boot(get_absolute_time());
    uint64_t t_last_print_us = t_last_us;
    printf("Bidirectional accumulator started\n");

    while (true) {
        if (!g_data_ready) {
            tight_loop_contents();
            continue;
        }
        g_data_ready = false;

        uint32_t t_now_us = to_us_since_boot(get_absolute_time());

        /* Signed instantaneous P_real: + consume, − export. */
        float p = 0.0f;
        rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p);
        float dt_s = (float)(t_now_us - t_last_us) / 1000000.0f;
        t_last_us = t_now_us;

        if (p > 0.0f) e_consumed_wh += (double)p * dt_s / 3600.0;
        else          e_exported_wh += (double)(-p) * dt_s / 3600.0;

        /* Summary print every 5 s — not on every RT window. */
        if (t_now_us - t_last_print_us >= 5000000UL) {
            t_last_print_us = t_now_us;
            printf("P=%+8.1fW   consumed=%.4f Wh  exported=%.4f Wh  net=%+.4f Wh\n",
                   p, e_consumed_wh, e_exported_wh,
                   e_consumed_wh - e_exported_wh);
        }
    }
}

Notes:

  • La función gpio_set_irq_enabled_with_callback() del Pico SDK registra un callback compartido para todas las IRQ de GPIO; las llamadas posteriores a gpio_set_irq_enabled() reutilizan ese callback.
  • volatile bool basta para una sincronización con un único indicador: el RP2040 es de emisión única y el booleano se lee de forma atómica.

Ejemplo 6: balance energético del hogar

Objetivo: panel de balance energético completo. Tres módulos:

  • rbAmp n.º 1 en la alimentación principal (STD: bidireccional)
  • rbAmp n.º 2 en la salida del inversor solar (BASIC válido)
  • rbAmp n.º 3, UI3, en tres cargas grandes (calefacción, AC, VE)

El maestro usa rbamp_io_broadcast_latch() para instantáneas síncronas y publica un saldo retenido por MQTT cada minuto.

C
#include 
#include 
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "rbamp_io.h"

#define ADDR_MAINS  0x50U
#define ADDR_SOLAR  0x51U
#define ADDR_LOADS  0x52U
#define REG_PERIOD_AVG_P_NEG_MAINS  0xFFU   /* set per SKU datasheet on STD */

extern void net_init(void);                  /* same boilerplate as Ex. 4 */
extern mqtt_client_t *s_mqtt;

typedef struct {
    double mains_in_wh;
    double mains_out_wh;
    double solar_total_wh;
    double loads_wh[3];
} totals_t;

int main(void) {
    stdio_init_all();
    sleep_ms(2000);
    net_init();
    rbamp_io_init(i2c0, 4, 5, 50000);
    rbamp_io_wait_ready(ADDR_MAINS, 2000);
    rbamp_io_wait_ready(ADDR_SOLAR, 2000);
    rbamp_io_wait_ready(ADDR_LOADS, 2000);

    /* Primer snapshot on all modules (general call). GC is opt-in
     * (FLEET_CONFIG.bit0, default OFF) — fall back to per-module on NACK. */
    uint16_t gc_tick = 0;
    if (rbamp_io_broadcast_latch(gc_tick++, 0) != PICO_OK) {
        rbamp_io_write_u8(ADDR_MAINS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
        rbamp_io_write_u8(ADDR_SOLAR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
        rbamp_io_write_u8(ADDR_LOADS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
    }
    uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());

    totals_t totals = {0};
    printf("Home balance started\n");

    while (true) {
        sleep_ms(60 * 1000);

        /* Synchronous snapshot on all modules. */
        if (rbamp_io_broadcast_latch(gc_tick++, 0) != PICO_OK) {
            rbamp_io_write_u8(ADDR_MAINS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
            rbamp_io_write_u8(ADDR_SOLAR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
            rbamp_io_write_u8(ADDR_LOADS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
        }
        uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
        sleep_ms(50);

        float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
        t_prev_ms = t_now_ms;

        /* ----- MAINS (bidirectional, STD) ----- */
        uint8_t valid;
        if (rbamp_io_read_u8(ADDR_MAINS, RB_REG_PERIOD_VALID, &valid) == PICO_OK
            && (valid & 0x01U)) {
            float p_consume = 0.0f, p_export = 0.0f;
            rbamp_io_read_float_le(ADDR_MAINS, RB_REG_PERIOD_AVG_P0, &p_consume);
            if (REG_PERIOD_AVG_P_NEG_MAINS != 0xFFU) {
                rbamp_io_read_float_le(ADDR_MAINS, REG_PERIOD_AVG_P_NEG_MAINS,
                                       &p_export);
            }
            totals.mains_in_wh  += (double)p_consume * dt_s / 3600.0;
            totals.mains_out_wh += (double)p_export  * dt_s / 3600.0;
        }

        /* ----- SOLAR (generation only) ----- */
        if (rbamp_io_read_u8(ADDR_SOLAR, RB_REG_PERIOD_VALID, &valid) == PICO_OK
            && (valid & 0x01U)) {
            float p = 0.0f;
            rbamp_io_read_float_le(ADDR_SOLAR, RB_REG_PERIOD_AVG_P0, &p);
            totals.solar_total_wh += (double)p * dt_s / 3600.0;
        }

        /* ----- LOADS (UI3, three channels) ----- */
        if (rbamp_io_read_u8(ADDR_LOADS, RB_REG_PERIOD_VALID, &valid) == PICO_OK
            && (valid & 0x01U)) {
            float p[3] = {0};
            rbamp_io_read_float_le(ADDR_LOADS, RB_REG_PERIOD_AVG_P0, &p[0]); /* I0 */
            rbamp_io_read_float_le(ADDR_LOADS, RB_REG_PERIOD_AVG_P1, &p[1]); /* I1 */
            rbamp_io_read_float_le(ADDR_LOADS, RB_REG_PERIOD_AVG_P2, &p[2]); /* I2 */
            for (int i = 0; i < 3; i++) {
                totals.loads_wh[i] += (double)p[i] * dt_s / 3600.0;
            }
        }

        double total_consumed = totals.mains_in_wh + totals.solar_total_wh
                              - totals.mains_out_wh;
        double solar_self_used = totals.solar_total_wh - totals.mains_out_wh;
        if (solar_self_used < 0.0) solar_self_used = 0.0;

        printf("MAINS  in=%.2f  out=%.2f\n", totals.mains_in_wh, totals.mains_out_wh);
        printf("SOLAR  gen=%.2f  self-used=%.2f  exported=%.2f\n",
               totals.solar_total_wh, solar_self_used, totals.mains_out_wh);
        printf("LOADS  HP=%.2f  AC=%.2f  EV=%.2f\n",
               totals.loads_wh[0], totals.loads_wh[1], totals.loads_wh[2]);
        printf("TOTAL  household consumed=%.2f Wh\n", total_consumed);

        char payload[512];
        int n = snprintf(payload, sizeof(payload),
            "{\"mains_in\":%.3f,\"mains_out\":%.3f,\"solar\":%.3f,"
            "\"self_used\":%.3f,\"total_consumed\":%.3f,"
            "\"hp\":%.3f,\"ac\":%.3f,\"ev\":%.3f}",
            totals.mains_in_wh, totals.mains_out_wh, totals.solar_total_wh,
            solar_self_used, total_consumed,
            totals.loads_wh[0], totals.loads_wh[1], totals.loads_wh[2]);
        mqtt_publish(s_mqtt, "home/energy/balance", payload, n,
                     /*qos*/ 1, /*retain*/ 1, NULL, NULL);
    }
}

Ejemplo 7: detección de eventos de corriente

Objetivo: en cada flanco de DRDY, comparar la P instantánea con una EMA y registrar en una tarjeta SD montada por SPI + FATFS las desviaciones significativas. Hardware: Pico + rbAmp + módulo de tarjeta SD por SPI. Biblioteca: no-OS-FatFS-SD-SPI-RPi-Pico u otro port de FATFS compatible con el SDK.

C
#include 
#include 
#include 
#include "pico/stdlib.h"
#include "hardware/gpio.h"
#include "ff.h"                          /* FATFS API */
#include "rbamp_io.h"

#define RB_ADDR    0x50U
#define PIN_DRDY   15

#define EMA_ALPHA          0.05f
#define EVENT_THRESHOLD_W  200.0f

static volatile bool g_data_ready = false;
static FATFS s_fs;
static FIL   s_logfile;

static void gpio_callback(uint gpio, uint32_t events) {
    if (gpio == PIN_DRDY && (events & GPIO_IRQ_EDGE_FALL)) {
        g_data_ready = true;
    }
}

/**
 * @brief  Mount the SD card and open events.log in append mode.
 */
static bool sd_setup(void) {
    if (f_mount(&s_fs, "", 1) != FR_OK) return false;
    if (f_open(&s_logfile, "events.log",
               FA_OPEN_APPEND | FA_WRITE) != FR_OK) return false;
    return true;
}

int main(void) {
    stdio_init_all();
    sleep_ms(2000);
    rbamp_io_init(i2c0, 4, 5, 50000);
    rbamp_io_wait_ready(RB_ADDR, 2000);

    if (sd_setup()) printf("SD mounted; logging to events.log\n");
    else            printf("WARN: SD card not available\n");

    gpio_init(PIN_DRDY);
    gpio_set_dir(PIN_DRDY, GPIO_IN);
    gpio_pull_up(PIN_DRDY);
    gpio_set_irq_enabled_with_callback(PIN_DRDY, GPIO_IRQ_EDGE_FALL,
                                        true, &gpio_callback);

    /* Seed the EMA with current power so we do not log a spurious startup event. */
    float p_ema = 0.0f;
    rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p_ema);
    printf("Event detector started\n");

    while (true) {
        if (!g_data_ready) { tight_loop_contents(); continue; }
        g_data_ready = false;

        float p = 0.0f;
        rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p);

        float delta = p - p_ema;
        p_ema = (1.0f - EMA_ALPHA) * p_ema + EMA_ALPHA * p;

        if (fabsf(delta) > EVENT_THRESHOLD_W) {
            const char *type = (delta > 0.0f) ? "TURN_ON" : "TURN_OFF";
            char line[128];
            int n = snprintf(line, sizeof(line),
                             "%lu  %s  delta=%+.1f W  P=%.1f W  EMA=%.1f W\n",
                             (unsigned long)to_ms_since_boot(get_absolute_time()),
                             type, delta, p, p_ema);
            printf("%s", line);
            UINT bw;
            f_write(&s_logfile, line, n, &bw);
            f_sync(&s_logfile);            /* flush to the card */
        }
    }
}

Ejemplo 8: publicador MQTT con descubrimiento automático de Home Assistant

Objetivo: una integración directa con HA. La Pico W se conecta a Wi-Fi y a un broker MQTT, publica configuraciones de auto-descubrimiento de HA (retenidas) y emite un estado en JSON cada minuto. Hardware: Pico W (o Pico 2 W) + un rbAmp UI1 + Wi-Fi + broker MQTT.

C
#include 
#include 
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "rbamp_io.h"

#define RB_ADDR     0x50U
#define DEVICE_ID   "rbamp_main"
#define DEVICE_NAME "Mains rbAmp"

extern void net_init(void);                /* Wi-Fi + MQTT bring-up (Ex. 4) */
extern mqtt_client_t *s_mqtt;

/**
 * @brief  Publish one HA discovery config (retained).
 */
static void publish_discovery_sensor(const char *key, const char *friendly,
                                     const char *unit, const char *dev_class,
                                     const char *state_class) {
    char topic[128], payload[512];
    snprintf(topic, sizeof(topic),
             "homeassistant/sensor/%s/%s/config", DEVICE_ID, key);

    int n = snprintf(payload, sizeof(payload),
        "{"
          "\"name\":\"%s %s\","
          "\"unique_id\":\"%s_%s\","
          "\"state_topic\":\"rbamp/%s/state\","
          "\"value_template\":\"{{ value_json.%s }}\","
          "\"state_class\":\"%s\","
          "\"device\":{"
            "\"identifiers\":[\"%s\"],"
            "\"name\":\"%s\","
            "\"manufacturer\":\"rbAmp\","
            "\"model\":\"rbAmp UI*\""
          "}",
        DEVICE_NAME, friendly, DEVICE_ID, key,
        DEVICE_ID, key, state_class,
        DEVICE_ID, DEVICE_NAME);
    if (unit)      n += snprintf(payload + n, sizeof(payload) - n,
                                  ",\"unit_of_measurement\":\"%s\"", unit);
    if (dev_class) n += snprintf(payload + n, sizeof(payload) - n,
                                  ",\"device_class\":\"%s\"", dev_class);
    n += snprintf(payload + n, sizeof(payload) - n, "}");

    mqtt_publish(s_mqtt, topic, payload, n,
                 /*qos*/ 1, /*retain*/ 1, NULL, NULL);
}

/**
 * @brief  Publish the full set of HA discovery configs for one rbAmp.
 */
static void publish_discovery_all(void) {
    publish_discovery_sensor("voltage",        "Voltage",        "V",   "voltage",        "measurement");
    publish_discovery_sensor("current",        "Current",        "A",   "current",        "measurement");
    publish_discovery_sensor("power",          "Power",          "W",   "power",          "measurement");
    publish_discovery_sensor("energy",         "Energy",         "Wh",  "energy",         "total_increasing");
    publish_discovery_sensor("frequency",      "Frequency",      "Hz",  "frequency",      "measurement");
    publish_discovery_sensor("power_factor",   "Power Factor",   NULL,  "power_factor",   "measurement");
    publish_discovery_sensor("apparent_power", "Apparent Power", "VA",  "apparent_power", "measurement");
    publish_discovery_sensor("reactive_power", "Reactive Power", "var", "reactive_power", "measurement");
}

/* Set to true by Ex.4's mqtt_conn_cb on MQTT_CONNECT_ACCEPTED.
 * (Add `extern volatile bool s_mqtt_connected;` to the net_init translation unit.) */
extern volatile bool s_mqtt_connected;

int main(void) {
    stdio_init_all();
    sleep_ms(2000);
    net_init();

    /* MQTT connect is asynchronous — publishing discovery before the CONNECT
     * callback fires causes mqtt_publish() to return ERR_CONN and the configs
     * to silently disappear. Wait (bounded) for the connection. */
    uint32_t mqtt_deadline = to_ms_since_boot(get_absolute_time()) + 15000;
    while (!s_mqtt_connected) {
        if (to_ms_since_boot(get_absolute_time()) > mqtt_deadline) {
            printf("WARN: MQTT not connected after 15 s — discovery will be retried on reconnect\n");
            break;
        }
        sleep_ms(100);
    }
    if (s_mqtt_connected) publish_discovery_all();

    rbamp_io_init(i2c0, 4, 5, 50000);
    rbamp_io_wait_ready(RB_ADDR, 2000);

    rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);  /* primer */
    uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
    double total_wh = 0.0;

    while (true) {
        sleep_ms(60 * 1000);

        rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
        uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
        sleep_ms(50);

        uint8_t valid = 0;
        rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
        if ((valid & 0x01U) == 0) {
            t_prev_ms = to_ms_since_boot(get_absolute_time());
            continue;
        }
        float avg_p = 0.0f;
        rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);
        float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
        total_wh += (double)avg_p * dt_s / 3600.0;
        t_prev_ms = t_now_ms;

        /* Live RT values for the state payload. */
        float u = 0, i_ = 0, pf = 0, q = 0;
        uint8_t freq = 0;
        rbamp_io_read_float_le(RB_ADDR, RB_REG_U_RMS,   &u);
        rbamp_io_read_float_le(RB_ADDR, RB_REG_I0_RMS,  &i_);
        rbamp_io_read_float_le(RB_ADDR, RB_REG_PF0,     &pf);
        rbamp_io_read_float_le(RB_ADDR, RB_REG_Q0,      &q);
        rbamp_io_read_u8     (RB_ADDR, RB_REG_AC_FREQ,  &freq);

        char payload[384];
        int n = snprintf(payload, sizeof(payload),
            "{"
              "\"voltage\":%.1f,"
              "\"current\":%.3f,"
              "\"power\":%.1f,"
              "\"energy\":%.3f,"
              "\"frequency\":%u,"
              "\"power_factor\":%.3f,"
              "\"apparent_power\":%.1f,"
              "\"reactive_power\":%.1f"
            "}",
            u, i_, avg_p, total_wh,
            (unsigned)freq, pf, u * i_, q);
        mqtt_publish(s_mqtt, "rbamp/" DEVICE_ID "/state", payload, n,
                     /*qos*/ 0, /*retain*/ 0, NULL, NULL);
        printf("Published: %s\n", payload);
    }
}

Ejemplo 9: registrador alimentado por batería con reposo latente

Objetivo: un registrador exterior / autónomo que se despierta del modo latente cada 10 minutos mediante la alarma RTC, toma una instantánea de un periodo, publica por MQTT y vuelve al modo latente. La Pico W alcanza unos cientos de µA en reposo latente: suficiente para muchos meses con una celda de Li-ion. Hardware: Pico W + un rbAmp UI1 + Li-ion. El rbAmp puede cortarse mediante un interruptor de lado alto en el GPIO 16. Persistencia: pico/sleep.h + el RTC del chip + una pequeña región NOINIT (o NVM externa) para el estado que debe sobrevivir al reposo.

C
#include 
#include 
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "pico/sleep.h"
#include "hardware/rtc.h"
#include "hardware/gpio.h"
#include "lwip/apps/mqtt.h"
#include "rbamp_io.h"

#define RB_ADDR        0x50U
#define PIN_RBAMP_POWER 16
#define WAKE_SECONDS    (10 * 60)

extern void net_init(void);
extern mqtt_client_t *s_mqtt;

/* "NOINIT" region — variables that are not zeroed by the startup code.
 * They survive dormant sleep on RP2040 because RAM stays powered. */
__attribute__((section(".uninitialized_data")))
static double   s_total_wh;
__attribute__((section(".uninitialized_data")))
static uint32_t s_wake_count;
__attribute__((section(".uninitialized_data")))
static bool     s_primer_done;
__attribute__((section(".uninitialized_data")))
static uint32_t s_magic;            /* 0xCAFEFEED when state is initialised */

/**
 * @brief  Power-gate the rbAmp module.
 */
static void rbamp_power(bool on) {
    gpio_init(PIN_RBAMP_POWER);
    gpio_set_dir(PIN_RBAMP_POWER, GPIO_OUT);
    gpio_put(PIN_RBAMP_POWER, on);
    if (on) sleep_ms(300);          /* let the LDO + MCU boot */
}

/**
 * @brief  Arm the RTC alarm `seconds` ahead (with day-wrap) and enter dormant sleep.
 * @details Execution resumes at the reset vector via watchdog. On Pico W,
 *          deinit CYW43 BEFORE calling this — leaving the radio powered keeps
 *          the chip at ~10 mA instead of ~180 µA in dormant.
 */
static void enter_dormant(uint32_t seconds) {
    datetime_t now;
    if (!rtc_get_datetime(&now)) {
        /* RTC not running — fall back to a brute reboot via watchdog. */
        watchdog_reboot(0, 0, seconds * 1000U);
        while (1) tight_loop_contents();
    }

    /* Convert "now" + `seconds` to absolute calendar time WITH day-wrap.
     * Without this, alarms in the last 60 s of a day land at 00:0x today —
     * a time in the past — and the RTC never matches until 24 h later. */
    int total_sec = now.hour * 3600 + now.min * 60 + now.sec + (int)seconds;
    int day_offset = total_sec / 86400;
    total_sec %= 86400;

    datetime_t alarm = now;
    alarm.hour = total_sec / 3600;
    alarm.min  = (total_sec / 60) % 60;
    alarm.sec  =  total_sec % 60;
    if (day_offset > 0) {
        /* Bump the day; for periods ≤ 24 h this is at most one day forward. */
        alarm.day += day_offset;
        /* NOTE: this does not handle month/year roll-over; for periods ≤ 24 h
         * and well-set RTC the simplest fix is to step the day field; for a
         * production logger use a proper time_t arithmetic via mktime. */
    }

    sleep_run_from_xosc();
    sleep_goto_sleep_until(&alarm, NULL);
    /* Force a clean reset so main() re-runs from the top (with NOINIT state). */
    watchdog_reboot(0, 0, 1);
    while (1) tight_loop_contents();
}

int main(void) {
    stdio_init_all();
    sleep_ms(1000);

    /* Initialise persistent state on cold boot. Write `s_magic` LAST so a
     * crash mid-init leaves the marker unset and forces re-initialisation. */
    if (s_magic != 0xCAFEFEEDU) {
        s_total_wh    = 0.0;
        s_wake_count  = 0;
        s_primer_done = false;
        __dmb();                    /* publish other fields before the marker */
        s_magic       = 0xCAFEFEEDU;

        /* Seed the RTC with an arbitrary epoch so rtc_get_datetime() returns
         * a valid struct from the first call. Without this, the alarm math in
         * enter_dormant() reads garbage and sleep duration is undefined. */
        rtc_init();
        datetime_t epoch = { .year=2024, .month=1, .day=1,
                              .dotw=1,  .hour=0,  .min=0, .sec=0 };
        rtc_set_datetime(&epoch);
        sleep_us(64);               /* RTC needs a few cycles to latch */
    } else {
        rtc_init();
    }
    s_wake_count++;

    /* Power up rbAmp + I2C. */
    rbamp_power(true);
    rbamp_io_init(i2c0, 4, 5, 50000);
    if (rbamp_io_wait_ready(RB_ADDR, 2000) != PICO_OK) {
        printf("rbAmp not ready — sleeping\n");
        rbamp_power(false);
        enter_dormant(WAKE_SECONDS);
    }

    /* First wake-up after a cold boot: primer snapshot only. */
    if (!s_primer_done) {
        rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
        s_primer_done = true;
        printf("Primer done — entering dormant\n");
        rbamp_power(false);
        enter_dormant(WAKE_SECONDS);
    }

    /* Subsequent wake-ups: close the period and read its average power. */
    rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
    sleep_ms(50);

    uint8_t valid = 0;
    rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
    if ((valid & 0x01U) == 0) {
        printf("Stale snapshot — skipping cycle\n");
        rbamp_power(false);
        enter_dormant(WAKE_SECONDS);
    }

    float avg_p = 0.0f;
    rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);
    /* dt approximation: dormant sleep + boot ≈ WAKE_SECONDS. For higher accuracy
     * read the RTC calendar on entry and exit. */
    float dt_s = (float)WAKE_SECONDS;
    s_total_wh += (double)avg_p * dt_s / 3600.0;

    /* Publish via Wi-Fi + MQTT (graceful fallback). */
    net_init();
    if (s_mqtt) {
        char payload[256];
        int n = snprintf(payload, sizeof(payload),
            "{\"wake\":%lu,\"dt_s\":%.1f,\"avg_p\":%.1f,\"energy_wh\":%.3f}",
            (unsigned long)s_wake_count, dt_s, avg_p, s_total_wh);
        mqtt_publish(s_mqtt, "rbamp/remote/state", payload, n,
                     /*qos*/ 1, /*retain*/ 1, NULL, NULL);
        printf("Published: %s\n", payload);
        sleep_ms(200);                   /* let LwIP flush the publish */
    } else {
        printf("Wi-Fi/MQTT failed — value buffered in NOINIT RAM\n");
    }

    /* Power down the CYW43 radio BEFORE dormant — leaving it powered keeps
     * the chip at ~10 mA instead of ~180 µA. Required for the headline
     * "6 months on a 2000 mAh cell" power budget. */
#if PICO_CYW43_SUPPORTED
    cyw43_arch_deinit();
#endif

    rbamp_power(false);
    enter_dormant(WAKE_SECONDS);
}

Notes:

  • La sección .uninitialized_data no se pone a cero en el arranque; sobrevive al breve reinicio que sigue al despertar del reposo latente. Un centinela de número mágico (s_magic) permite distinguir un arranque en frío (RAM sin inicializar, magia aleatoria) de un despertar.
  • Para una persistencia permanente tras retirar la batería, guarde periódicamente el total en la memoria flash interna con flash_range_program(). El SDK de Pico tiene buenos ejemplos en pico-examples/flash/.
  • Un Pico W en suspensión latente con el CYW43 apagado consume unos 1 mA. El RP2040 solo (Pico) baja a unos 180 µA. Use cyw43_arch_deinit() antes de dormir para apagar el módulo de radio.

Ejemplo 10: tarifa por franjas horarias (TOU) con hora de pared SNTP

Objetivo: facturar la energía según una tarifa por franjas horarias. La Pico W mantiene un reloj de pared real mediante SNTP, reparte cada periodo cerrado en el tramo tarifario correspondiente, reinicia los totales diarios a medianoche y publica cargas con marcas de tiempo ISO. Hardware: Pico W + un rbAmp UI1 + Wi-Fi.

Adiciones a CMakeLists.txt:

CMake
target_link_libraries(example_10
    pico_stdlib
    hardware_i2c
    pico_cyw43_arch_lwip_threadsafe_background
    pico_lwip_mqtt
    pico_lwip_sntp)

src/example_10.c:

C
#include 
#include 
#include 
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "lwip/apps/sntp.h"
#include "rbamp_io.h"

#define RB_ADDR  0x50U

/* CEST = UTC+2. For full DST handling, recompute on roll-over. */
#define TZ_OFFSET_HOURS  2
#define PEAK_START_HOUR  8
#define PEAK_END_HOUR    22

extern void net_init(void);
extern mqtt_client_t *s_mqtt;

typedef struct {
    double peak_wh, off_peak_wh;
    int    day_of_year;
} day_totals_t;
typedef struct {
    double peak_wh, off_peak_wh;
} lifetime_totals_t;

static day_totals_t      s_today    = { .day_of_year = -1 };
static lifetime_totals_t s_lifetime = { 0 };

/**
 * @brief  Start SNTP and wait until the C library `time(NULL)` returns plausible UTC.
 */
static bool sntp_sync(uint32_t timeout_ms) {
    sntp_setoperatingmode(SNTP_OPMODE_POLL);
    sntp_setservername(0, "pool.ntp.org");
    sntp_setservername(1, "time.google.com");
    sntp_init();

    absolute_time_t deadline = make_timeout_time_ms(timeout_ms);
    while (!time_reached(deadline)) {
        time_t now = time(NULL);
        if (now > 1700000000) {                  /* ≥ year 2023 */
            struct tm lt;
            gmtime_r(&now, <);
            printf("SNTP sync: %04d-%02d-%02d %02d:%02d:%02d UTC\n",
                   lt.tm_year + 1900, lt.tm_mon + 1, lt.tm_mday,
                   lt.tm_hour, lt.tm_min, lt.tm_sec);
            return true;
        }
        sleep_ms(500);
    }
    return false;
}

static struct tm local_time(void) {
    time_t now = time(NULL) + (TZ_OFFSET_HOURS * 3600);
    struct tm lt;
    gmtime_r(&now, <);
    return lt;
}

static bool is_peak_hour(int hour) {
    return (hour >= PEAK_START_HOUR) && (hour < PEAK_END_HOUR);
}

static void iso_now(char *out, size_t out_len) {
    struct tm lt = local_time();
    char sign = (TZ_OFFSET_HOURS >= 0) ? '+' : '-';
    int off = (TZ_OFFSET_HOURS < 0) ? -TZ_OFFSET_HOURS : TZ_OFFSET_HOURS;
    snprintf(out, out_len, "%04d-%02d-%02dT%02d:%02d:%02d%c%02d00",
             lt.tm_year + 1900, lt.tm_mon + 1, lt.tm_mday,
             lt.tm_hour, lt.tm_min, lt.tm_sec, sign, off);
}

/**
 * @brief  Add one period's energy to the right bucket; roll over the day at midnight.
 */
static void accumulate(double e_wh, const struct tm *tm_now) {
    if (s_today.day_of_year != tm_now->tm_yday) {
        if (s_today.day_of_year >= 0) {
            char payload[192];
            int n = snprintf(payload, sizeof(payload),
                "{\"yday\":%d,\"peak_wh\":%.3f,\"off_peak_wh\":%.3f,"
                 "\"total_wh\":%.3f}",
                s_today.day_of_year, s_today.peak_wh, s_today.off_peak_wh,
                s_today.peak_wh + s_today.off_peak_wh);
            mqtt_publish(s_mqtt, "rbamp/tou/day_close", payload, n,
                         /*qos*/ 1, /*retain*/ 1, NULL, NULL);
            printf("Day closed: %s\n", payload);
        }
        s_today.peak_wh = 0.0;
        s_today.off_peak_wh = 0.0;
        s_today.day_of_year = tm_now->tm_yday;
    }
    if (is_peak_hour(tm_now->tm_hour)) {
        s_today.peak_wh    += e_wh;
        s_lifetime.peak_wh += e_wh;
    } else {
        s_today.off_peak_wh    += e_wh;
        s_lifetime.off_peak_wh += e_wh;
    }
}

int main(void) {
    stdio_init_all();
    sleep_ms(2000);
    net_init();
    sntp_sync(15000);

    rbamp_io_init(i2c0, 4, 5, 50000);
    rbamp_io_wait_ready(RB_ADDR, 2000);
    rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);  /* primer */
    uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
    printf("TOU started: peak %02d:00..%02d:00 local\n",
           PEAK_START_HOUR, PEAK_END_HOUR);

    while (true) {
        sleep_ms(60 * 1000);

        rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
        uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
        sleep_ms(50);

        uint8_t valid = 0;
        rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
        if ((valid & 0x01U) == 0) {
            t_prev_ms = to_ms_since_boot(get_absolute_time());
            continue;
        }
        float avg_p = 0.0f;
        rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);
        float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
        double e_wh = (double)avg_p * dt_s / 3600.0;
        t_prev_ms = t_now_ms;

        struct tm lt = local_time();
        if (lt.tm_year + 1900 < 2023) {
            printf("WARN: clock not synced — retrying SNTP\n");
            sntp_sync(15000);
            continue;
        }
        accumulate(e_wh, <);
        bool peak = is_peak_hour(lt.tm_hour);

        char iso[40];
        iso_now(iso, sizeof(iso));

        char payload[384];
        int n = snprintf(payload, sizeof(payload),
            "{"
              "\"ts\":\"%s\","
              "\"tariff\":\"%s\","
              "\"avg_p\":%.1f,"
              "\"period_wh\":%.4f,"
              "\"today_peak_wh\":%.3f,"
              "\"today_off_peak_wh\":%.3f,"
              "\"life_peak_wh\":%.3f,"
              "\"life_off_peak_wh\":%.3f"
            "}",
            iso, peak ? "peak" : "off_peak",
            avg_p, e_wh,
            s_today.peak_wh, s_today.off_peak_wh,
            s_lifetime.peak_wh, s_lifetime.off_peak_wh);
        mqtt_publish(s_mqtt, "rbamp/tou/state", payload, n,
                     /*qos*/ 0, /*retain*/ 0, NULL, NULL);
        printf("%s\n", payload);
    }
}

Notes:

  • pico_lwip_sntp se conecta al cliente SNTP de LwIP; el SDK lo enlaza con time(NULL) de la biblioteca C, de modo que gmtime_r() funciona sin más.
  • Para un manejo completo del horario de verano, guarde el desfase TZ en una pequeña tabla, o incluya en la compilación una cadena TZ POSIX mediante el mecanismo tzset() de newlib si su build lo incluye.
  • Para la medición bidireccional de un STD, llame a accumulate() dos veces: una para el consumo y otra para la exportación, y publique ambos cubos punta / valle.

Comparación de ejemplos

# Complejidad Salida MQTT DRDY Multimódulo Bidireccional Persistencia Caso de uso
1 mínimo stdio USB — — — — — prueba de humo
2 bajo OLED — — — — RAM medidor en caja
3 bajo stdio USB — — sí (3) — — monitorización doméstica
4 medio — sí — — — RAM por electrodoméstico en HA
5 medio stdio USB — sí — sí (maestro) RAM vivienda solar en nivel BASIC
6 alta — sí — sí (3) sí RAM balance energético de toda la casa
7 medio USB + SD (FATFS) — sí — — Tarjeta SD detección de eventos
8 medio — sí (+disco) — — opcional RAM + MQTT Auto-descubrimiento de HA
9 medio — sí — — — RAM NOINIT registrador exterior / autónomo
10 medio stdio USB sí — — opcional RAM + MQTT TOU punta/fuera de punta con SNTP

Buenas prácticas

  • Compruebe siempre los códigos de retorno de las llamadas rbamp_io_*. Las transacciones I²C pueden fallar en buses largos; el código de producción debe reintentar en lugar de ignorar el fallo.
  • Mantenga las callbacks de IRQ de GPIO muy simples. El SDK de Pico usa una única callback compartida para todas las IRQ de GPIO: ponga un volatile bool a true y regrese. Todo el trabajo de I²C y printf pertenece al bucle principal.
  • Use i2c0 e i2c1 de forma independiente. rbAmp en i2c0, OLED en i2c0, tarjeta SD en SPI: mantenga cada periférico en el bus para el que fue inicializado.
  • Use to_ms_since_boot(get_absolute_time()) para el reloj maestro. Precisión de microsegundos con to_us_since_boot(). Monotónico; sobrevive a sleep_ms().
  • PERIOD_VALID (0x07) debe comprobarse tras cada CMD_LATCH_PERIOD. Las instantáneas obsoletas aparecen si el maestro consulta más rápido de lo que integra el firmware.
  • Espere ≥ 50 ms tras una instantánea antes de leer 0xDC..0xEF.
  • Para configuraciones con varios módulos, rbamp_io_broadcast_latch(tick, group) mediante llamada general ofrece una sincronización precisa. La recepción GC es opcional por módulo (FLEET_CONFIG.bit0, por defecto desactivada). Si hay NACK, recurra a la instantánea secuencial por módulo.
  • Para aplicaciones con batería en Pico W, desinicialice CYW43 (cyw43_arch_deinit()) antes de dormir para eliminar varios mA. El reposo latente del RP2040 es ~180 µA, y el del RP2350 aún menor.
  • Guarde los totales de Wh en la memoria flash interna con flash_range_program() si necesita que sobrevivan a una pérdida total de alimentación. La RAM NOINIT sobrevive al reposo latente, pero no a un corte de alimentación.
  • El soporte de flotantes en printf está activado por defecto en pico_stdlib. En RP2040 se usa la implementación pico_float del SDK; en RP2350, el soporte de FPU por hardware está activado por defecto.

Lo siguiente

Tras repasar estos diez ejemplos: