15 · Exemples Raspberry Pi Pico SDK
Ce chapitre est l'équivalent Raspberry Pi Pico de arduino-examples.md, micropython-examples.md, esp-idf-examples.md et stm32-hal-examples.md : les mêmes dix scénarios, portés en C natif avec le Pico SDK (pico-sdk 1.5+ / 2.x), avec une mise en réseau basée sur LwIP.
Ces exemples dialoguent directement avec rbAmp via l'API I²C brute. Ils sont destinés à un firmware embarqué de production sur RP2040 / RP2350 — contrôle direct du cœur double Cortex-M0+ / M33, intégration avec le client MQTT LwIP, FATFS et les primitives de veille et de persistance du SDK.
Aucune bibliothèque Pico SDK dédiée n'est livrée — les bibliothèques clientes couvrent Arduino (y compris arduino-pico pour RP2040 via l'API Wire), MicroPython (fonctionne sur le port RP2040), ESP-IDF et CPython sous Linux SBC ; voir le tableau des bibliothèques clientes du README. Pour du firmware Pico SDK natif en C, suivez les recettes d'API brute ci-dessous. Si vous voulez une API de plus haut niveau sur RP2040, le plus simple est le cœur arduino-pico + la bibliothèque Arduino rbAmp.
Cibles prises en charge et chaîne d'outils
| Cible | Validé | Wi-Fi | Remarques |
|---|---|---|---|
| Raspberry Pi Pico (RP2040) | ✓ | non | Exemples I²C seuls 1 à 3, 5, 7 |
| Raspberry Pi Pico W (RP2040 + CYW43) | ✓ | oui | Tous les exemples ; utilise pico-cyw43-arch + LwIP |
| Raspberry Pi Pico 2 (RP2350) | ✓ | non | Cortex-M33 |
| Raspberry Pi Pico 2 W (RP2350 + CYW43) | ✓ | oui | Tous les exemples |
Chaîne d'outils : pico-sdk 1.5.1+ (ou 2.x pour RP2350), CMake 3.13+, arm-none-eabi-gcc 12+ ; l'extension VS Code officielle « Raspberry Pi Pico » est recommandée.
Structure du projet
Chaque exemple utilise la structure standard de projet pico-sdk :
example_NN/
├── CMakeLists.txt
├── pico_sdk_import.cmake
└── src/
├── example_NN.c
├── rbamp_io.h
├── rbamp_io.c
└── lwipopts.h (only for Wi-Fi examples)
CMakeLists.txt de premier niveau :
cmake_minimum_required(VERSION 3.13)
# Pull in the SDK before project() — see pico-sdk template.
include(pico_sdk_import.cmake)
# For Pico W, set BOARD before project():
# set(PICO_BOARD pico_w)
project(example_NN C CXX ASM)
set(CMAKE_C_STANDARD 11)
pico_sdk_init()
add_executable(example_NN
src/example_NN.c
src/rbamp_io.c)
target_include_directories(example_NN PRIVATE src)
# Always-required libraries.
target_link_libraries(example_NN
pico_stdlib
hardware_i2c)
# Wi-Fi examples add CYW43 + LwIP + mqtt:
# target_link_libraries(example_NN
# pico_cyw43_arch_lwip_threadsafe_background
# pico_lwip_mqtt
# pico_lwip_sntp)
# target_compile_definitions(example_NN PRIVATE WIFI_SSID=\"...\" WIFI_PASSWORD=\"...\")
# Route stdio to USB CDC (for Pico's serial console).
pico_enable_stdio_usb(example_NN 1)
pico_enable_stdio_uart(example_NN 0)
pico_add_extra_outputs(example_NN)
Compiler et téléverser :
mkdir build && cd build
cmake ..
make -j
# Drag-and-drop the .uf2 onto the RPI-RP2 / RP2350 USB mass-storage device.
Table des matières des exemples
| # | Titre | Difficulté | Sortie | MQTT | DRDY | Multi-modules | Bidirectionnel | Cas d'usage |
|---|---|---|---|---|---|---|---|---|
| 1 | Lecture rapide | minimal | USB stdio | — | — | — | — | Test de fonctionnement |
| 2 | Compteur d'énergie sur 60 secondes sur OLED | faible | SSD1306 | — | — | — | — | Compteur Wh encapsulé |
| 3 | Surveillance multi-modules | faible | USB stdio | — | — | oui (3) | — | Surveillance de tout le foyer |
| 4 | Suivi d'énergie par appareil (UI3) | moyen | — | oui | — | — | — | Sous-comptage dans HA |
| 5 | Bidirectionnel côté maître sur un module BASIC | moyen | USB stdio | — | oui | — | oui (maître) | Maison solaire en gamme BASIC |
| 6 | Bilan énergétique de la maison | élevé | — | oui | — | oui (3) | oui | Bilan complet de la maison |
| 7 | Détection d'événements de puissance | moyen | USB + SD | — | oui | — | — | Journal des événements des appareils |
| 8 | Publication MQTT avec découverte automatique HA | moyen | — | oui (+disco) | — | — | facultatif | Intégration HA prête à l'emploi |
| 9 | Enregistreur sur batterie avec veille dormante | moyen | — | oui | — | — | — | Compteur hors réseau / extérieur |
| 10 | Tarification selon l'heure (TOU) avec horloge murale SNTP | moyen | USB stdio | oui | — | — | facultatif | Mesure tarifaire heures pleines / heures creuses |
Les exemples Wi-Fi (4, 6, 8, 9, 10) nécessitent un Pico W ou un Pico 2 W.
Fonctions utilitaires communes (rbamp_io.h / rbamp_io.c)
Placez ces fichiers dans le répertoire src/ de votre projet. Pour gagner de la place, la ligne #include "rbamp_io.h" est omise dans chaque exemple ci-dessous.
rbamp_io.h
/**
* @file rbamp_io.h
* @brief Raw I2C helpers for the rbAmp slave (Raspberry Pi Pico SDK).
*/
#pragma once
#include
#include
#include "pico/stdlib.h"
#include "hardware/i2c.h"
#ifdef __cplusplus
extern "C" {
#endif
#define RBAMP_I2C_TIMEOUT_US 50000U /* 50 ms */
/**
* @brief Initialise the I2C peripheral and pin functions.
* @param i2c_inst i2c0 or i2c1.
* @param sda_gpio SDA GPIO number (e.g. 4 for default i2c0).
* @param scl_gpio SCL GPIO number (e.g. 5 for default i2c0).
* @param baudrate Bus speed (use 50000 — the recommended 50 kHz; wrap reads in a short retry, see ch. 11 §2.2).
*/
void rbamp_io_init(i2c_inst_t *i2c_inst, uint sda_gpio, uint scl_gpio,
uint baudrate);
/**
* @brief Read one byte from a register of an rbAmp slave.
* @return PICO_OK on success, an error code otherwise.
*/
int rbamp_io_read_u8(uint8_t addr, uint8_t reg, uint8_t *out);
/**
* @brief Read a little-endian float32 from four consecutive registers.
* @details Reads four consecutive bytes. rbAmp supports READ auto-increment
* (a single burst-read is valid for atomicity). The per-byte form
* is shown for clarity. See chapter 11 for asymmetry rules.
*/
int rbamp_io_read_float_le(uint8_t addr, uint8_t reg, float *out);
/**
* @brief Read a little-endian uint32 from four consecutive registers.
*/
int rbamp_io_read_u32_le(uint8_t addr, uint8_t reg, uint32_t *out);
/**
* @brief Write a single byte to a register.
*/
int rbamp_io_write_u8(uint8_t addr, uint8_t reg, uint8_t val);
/**
* @brief Broadcast CMD_LATCH_PERIOD to every rbAmp with GC reception
* enabled (FLEET_CONFIG.bit0 = 1; opt-in, default OFF).
* @details Canonical 5-byte general-call frame: A5 27 group tick_lo tick_hi.
* Slaves reject any first byte != 0xA5. See chapter 11 §6.3.2.
* @param tick16 Caller's 16-bit window counter (mirrored at GC_TICK 0x59).
* @param group GROUP_ID filter (0 = all-call).
* @return PICO_OK on ACK; PICO_ERROR_GENERIC on NACK — fall back to per-module.
*/
int rbamp_io_broadcast_latch(uint16_t tick16, uint8_t group);
/**
* @brief Probe whether a slave responds at the given address.
* @return true if the slave acks, false otherwise.
*/
bool rbamp_io_probe(uint8_t addr);
/**
* @brief Block until DATA_VALID bit 0 of register 0xCE reads 1, or timeout.
* @return PICO_OK on success, PICO_ERROR_TIMEOUT otherwise.
*/
int rbamp_io_wait_ready(uint8_t addr, uint32_t timeout_ms);
/* ===== rbAmp register addresses (subset used in examples) ===== */
#define RB_REG_STATUS 0x00U
#define RB_REG_COMMAND 0x01U
#define RB_REG_VERSION 0x03U
#define RB_REG_AC_FREQ 0x20U
#define RB_REG_PERIOD_VALID 0x07U
#define RB_REG_U_RMS 0x86U
#define RB_REG_I0_RMS 0x8EU
#define RB_REG_I1_RMS 0x92U
#define RB_REG_I2_RMS 0x96U
#define RB_REG_P0_REAL 0xA6U
#define RB_REG_PF0 0xB2U
#define RB_REG_Q0 0xD0U
#define RB_REG_DATA_VALID 0xCEU
#define RB_REG_PERIOD_AVG_P0 0xDCU
#define RB_REG_PERIOD_AVG_P1 0xC2U
#define RB_REG_PERIOD_AVG_P2 0xC6U
#define RB_REG_PERIOD_MAX_P 0xE0U
#define RB_REG_PERIOD_LATCH_MS 0xECU
/* ===== Commands ===== */
#define RB_CMD_RESET 0x01U
#define RB_CMD_LATCH_PERIOD 0x27U
#ifdef __cplusplus
}
#endif
rbamp_io.c
#include "rbamp_io.h"
#include
#include "pico/error.h"
static i2c_inst_t *s_i2c = NULL;
void rbamp_io_init(i2c_inst_t *i2c_inst, uint sda_gpio, uint scl_gpio,
uint baudrate) {
s_i2c = i2c_inst;
i2c_init(s_i2c, baudrate);
gpio_set_function(sda_gpio, GPIO_FUNC_I2C);
gpio_set_function(scl_gpio, GPIO_FUNC_I2C);
/* The rbAmp board carries its own pull-ups; do NOT enable the internal
* pulls unless yours are physically removed. */
}
/**
* @brief Internal helper — one register read.
* @details Pattern: write reg-address (nostop=true) + read 1 byte.
*/
static int read_one(uint8_t addr, uint8_t reg, uint8_t *out) {
int n = i2c_write_timeout_us(s_i2c, addr, ®, 1,
/*nostop=*/true, RBAMP_I2C_TIMEOUT_US);
if (n != 1) return PICO_ERROR_GENERIC;
n = i2c_read_timeout_us(s_i2c, addr, out, 1,
/*nostop=*/false, RBAMP_I2C_TIMEOUT_US);
return (n == 1) ? PICO_OK : PICO_ERROR_GENERIC;
}
int rbamp_io_read_u8(uint8_t addr, uint8_t reg, uint8_t *out) {
return read_one(addr, reg, out);
}
int rbamp_io_read_float_le(uint8_t addr, uint8_t reg, float *out) {
uint8_t buf[4];
for (int i = 0; i < 4; i++) {
int rc = read_one(addr, (uint8_t)(reg + i), &buf[i]);
if (rc != PICO_OK) return rc;
}
memcpy(out, buf, sizeof(float)); /* RP2040 / RP2350 are little-endian */
return PICO_OK;
}
int rbamp_io_read_u32_le(uint8_t addr, uint8_t reg, uint32_t *out) {
uint8_t buf[4];
for (int i = 0; i < 4; i++) {
int rc = read_one(addr, (uint8_t)(reg + i), &buf[i]);
if (rc != PICO_OK) return rc;
}
*out = (uint32_t)buf[0] | (uint32_t)buf[1] << 8
| (uint32_t)buf[2] << 16 | (uint32_t)buf[3] << 24;
return PICO_OK;
}
int rbamp_io_write_u8(uint8_t addr, uint8_t reg, uint8_t val) {
uint8_t tx[2] = { reg, val };
int n = i2c_write_timeout_us(s_i2c, addr, tx, 2,
/*nostop=*/false, RBAMP_I2C_TIMEOUT_US);
return (n == 2) ? PICO_OK : PICO_ERROR_GENERIC;
}
int rbamp_io_broadcast_latch(uint16_t tick16, uint8_t group) {
/* Canonical 5-byte general-call frame: A5 27 group tick_lo tick_hi. */
uint8_t tx[5] = {
0xA5, /* frame magic */
RB_CMD_LATCH_PERIOD, /* opcode 0x27 */
group, /* group_id (0 = all-call) */
(uint8_t)(tick16 & 0xFF),
(uint8_t)((tick16 >> 8) & 0xFF),
};
int n = i2c_write_timeout_us(s_i2c, /*addr=*/0x00U, tx, sizeof tx,
/*nostop=*/false, RBAMP_I2C_TIMEOUT_US);
return (n == (int)sizeof tx) ? PICO_OK : PICO_ERROR_GENERIC;
}
bool rbamp_io_probe(uint8_t addr) {
uint8_t dummy;
/* A 1-byte read is the simplest ACK probe — read the STATUS register. */
return read_one(addr, RB_REG_STATUS, &dummy) == PICO_OK;
}
int rbamp_io_wait_ready(uint8_t addr, uint32_t timeout_ms) {
absolute_time_t deadline = make_timeout_time_ms(timeout_ms);
while (!time_reached(deadline)) {
uint8_t v = 0;
if (rbamp_io_read_u8(addr, RB_REG_DATA_VALID, &v) == PICO_OK
&& (v & 0x01U)) {
return PICO_OK;
}
sleep_ms(50);
}
return PICO_ERROR_TIMEOUT;
}
Exemple 1 — Lecture rapide (minimale)
Objectif : afficher U, I, P, PF sur USB CDC une fois par seconde. Matériel : Raspberry Pi Pico + un rbAmp UI1. I²C sur GPIO 4 (SDA) / GPIO 5 (SCL) — broches par défaut de i2c0.
src/example_01.c:
#include
#include "pico/stdlib.h"
#include "hardware/i2c.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
int main(void) {
stdio_init_all(); /* USB CDC stdio */
sleep_ms(2000); /* let the USB host enumerate */
/* I2C0 on GPIO 4 / 5 at the recommended 50 kHz. */
rbamp_io_init(i2c0, 4, 5, 50000);
/* Wait until the first RT window has been computed. */
if (rbamp_io_wait_ready(RB_ADDR, 2000) != PICO_OK) {
printf("ERROR: rbAmp not ready\n");
while (1) tight_loop_contents();
}
uint8_t ver = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_VERSION, &ver);
printf("rbAmp version: 0x%02X\n", ver);
while (true) {
float u, i_, p, pf;
rbamp_io_read_float_le(RB_ADDR, RB_REG_U_RMS, &u );
rbamp_io_read_float_le(RB_ADDR, RB_REG_I0_RMS, &i_);
rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p );
rbamp_io_read_float_le(RB_ADDR, RB_REG_PF0, &pf);
printf("U=%.1fV I=%.3fA P=%+.1fW PF=%+.3f\n", u, i_, p, pf);
sleep_ms(1000);
}
}
Sortie console série attendue :
rbAmp version: 0x04
U=230.1V I=0.262A P=+60.2W PF=+0.998
U=229.9V I=0.262A P=+60.1W PF=+0.998
...
Connectez-vous à la console série avec minicom -D /dev/ttyACM0 -b 115200 (Linux), screen /dev/cu.usbmodem* (macOS) ou PuTTY (Windows).
Exemple 2 — compteur d'énergie de 60 secondes sur OLED
Objectif : compteur Wh rafraîchi une fois par minute, affiché sur un SSD1306 de 128×64 partageant le bus I²C de rbAmp. Matériel : Pico + rbAmp + SSD1306 (0x3C) sur le même bus. Bibliothèque : un pilote SSD1306 standard du Pico SDK (par ex. daschr/pico-ssd1306). L'API OLED ci-dessous est symbolique — remplacez-la par les appels de votre pilote.
#include
#include
#include "pico/stdlib.h"
#include "rbamp_io.h"
#include "ssd1306.h"
#define RB_ADDR 0x50U
int main(void) {
stdio_init_all();
sleep_ms(2000);
rbamp_io_init(i2c0, 4, 5, 50000);
/* OLED shares the same i2c0. */
ssd1306_t oled;
ssd1306_init(&oled, 128, 64, 0x3C, i2c0);
rbamp_io_wait_ready(RB_ADDR, 2000);
/* Primer snapshot — discard its snapshot. */
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
double total_wh = 0.0;
while (true) {
sleep_ms(60 * 1000);
/* 1) Final snapshot. */
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
sleep_ms(50); /* let firmware finalise snapshot */
/* 2) Check PERIOD_VALID. */
uint8_t valid = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
if ((valid & 0x01U) == 0) {
printf("WARN: stale snapshot\n");
t_prev_ms = to_ms_since_boot(get_absolute_time());
continue;
}
/* 3) Read time-averaged P. */
float avg_p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);
/* 4) Energy uses the MASTER clock. */
float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
double e_wh = (double)avg_p * dt_s / 3600.0;
total_wh += e_wh;
t_prev_ms = t_now_ms;
/* 5) Render. */
char line[32];
ssd1306_clear(&oled);
snprintf(line, sizeof(line), "P: %6.1f W", avg_p);
ssd1306_draw_string(&oled, 0, 0, 1, line);
snprintf(line, sizeof(line), "dt: %6.1f s", dt_s);
ssd1306_draw_string(&oled, 0, 16, 1, line);
snprintf(line, sizeof(line), "%.2f Wh", total_wh);
ssd1306_draw_string(&oled, 0, 32, 2, line);
ssd1306_show(&oled);
printf("avg_P=%.1f E_period=%.3f total=%.3f\n", avg_p, e_wh, total_wh);
}
}
Le pilote OLED et rbAmp partagent i2c0 — n'appelez jamais i2c_init() deux fois ; la fonction rbamp_io_init() de l'aide l'a déjà fait.
Exemple 3 — Surveillance multi-modules
Objectif : interroger trois modules (alimentation principale, chauffe-eau, climatisation) et afficher le total. Matériel : Pico + 3 × rbAmp UI1 à 0x50, 0x51, 0x52.
#include
#include
#include "pico/stdlib.h"
#include "rbamp_io.h"
typedef struct {
uint8_t addr;
const char *label;
} module_t;
static const module_t modules[] = {
{ 0x50, "Mains " },
{ 0x51, "Boiler" },
{ 0x52, "AC " },
};
#define N_MODULES (sizeof(modules) / sizeof(modules[0]))
int main(void) {
stdio_init_all();
sleep_ms(2000);
rbamp_io_init(i2c0, 4, 5, 50000);
/* Probe every module before entering the read loop. */
for (size_t i = 0; i < N_MODULES; i++) {
if (!rbamp_io_probe(modules[i].addr)) {
printf("ERROR: %s at 0x%02X not found\n",
modules[i].label, modules[i].addr);
while (1) tight_loop_contents();
}
}
printf("All modules OK\n");
while (true) {
float total_p = 0.0f;
printf("---\n");
/* Round-robin read. */
for (size_t i = 0; i < N_MODULES; i++) {
float u = 0.0f, p = 0.0f;
rbamp_io_read_float_le(modules[i].addr, RB_REG_U_RMS, &u);
rbamp_io_read_float_le(modules[i].addr, RB_REG_P0_REAL, &p);
printf("[%s] U=%.1f P=%+.1f W\n", modules[i].label, u, p);
total_p += p;
}
printf("TOTAL: %.1f W\n", total_p);
sleep_ms(2000);
}
}
Exemple 4 — Suivi d'énergie par appareil (UI3)
Objectif : un module UI3 avec trois pinces de courant sur trois charges différentes sur la même phase ; compteurs Wh indépendants publiés sur MQTT chaque minute. Matériel : Pico W (ou Pico 2 W) + 1 × rbAmp UI3 + réseau Wi-Fi avec un broker MQTT. Éléments du SDK : pico_cyw43_arch_lwip_threadsafe_background, pico_lwip_mqtt.
Ajouts au CMakeLists.txt :
set(PICO_BOARD pico_w)
target_link_libraries(example_04
pico_stdlib
hardware_i2c
pico_cyw43_arch_lwip_threadsafe_background
pico_lwip_mqtt)
target_compile_definitions(example_04 PRIVATE
WIFI_SSID=\"ssid\"
WIFI_PASSWORD=\"password\"
MQTT_BROKER_IP=\"192.168.1.10\")
src/lwipopts.h (minimal — à étendre depuis pico-examples/pico_w/wifi/lwipopts_examples_common.h) :
#pragma once
#include "lwip/apps/mqtt.h"
#define LWIP_MQTT 1
#define MEMP_NUM_SYS_TIMEOUT 8
/* Use the SDK's standard threadsafe-background opts. */
src/example_04.c:
#include
#include
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "lwip/dns.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
static const char *CH_NAMES[3] = { "main", "heatpump", "lights" };
static mqtt_client_t *s_mqtt;
static ip_addr_t s_broker_ip;
/**
* @brief MQTT connection-status callback (logs result; could trigger retry).
*/
static void mqtt_conn_cb(mqtt_client_t *client, void *arg,
mqtt_connection_status_t status) {
printf("MQTT connect status=%d\n", (int)status);
}
/**
* @brief Bring up Wi-Fi (CYW43) and connect to the MQTT broker.
*/
static void net_init(void) {
if (cyw43_arch_init()) {
printf("CYW43 init failed\n");
return;
}
cyw43_arch_enable_sta_mode();
if (cyw43_arch_wifi_connect_timeout_ms(WIFI_SSID, WIFI_PASSWORD,
CYW43_AUTH_WPA2_AES_PSK, 30000)) {
printf("Wi-Fi connect failed\n");
return;
}
printf("Wi-Fi up\n");
ipaddr_aton(MQTT_BROKER_IP, &s_broker_ip);
s_mqtt = mqtt_client_new();
struct mqtt_connect_client_info_t ci = { .client_id = "rbamp-ui3" };
mqtt_client_connect(s_mqtt, &s_broker_ip, 1883, mqtt_conn_cb, NULL, &ci);
}
/**
* @brief Publish one channel's state to MQTT.
*/
static void mqtt_publish_channel(const char *ch_name, float avg_p, double e_wh) {
char topic[64], payload[64];
snprintf(topic, sizeof(topic), "rbamp/%s/state", ch_name);
int n = snprintf(payload, sizeof(payload),
"{\"power\":%.1f,\"energy\":%.4f}", avg_p, e_wh);
mqtt_publish(s_mqtt, topic, payload, n, /*qos*/ 0, /*retain*/ 0,
NULL, NULL);
}
int main(void) {
stdio_init_all();
sleep_ms(2000);
net_init();
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(RB_ADDR, 2000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD); /* primer */
uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
double total_wh[3] = { 0.0, 0.0, 0.0 };
while (true) {
sleep_ms(60 * 1000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
sleep_ms(50);
uint8_t valid = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
if ((valid & 0x01U) == 0) {
t_prev_ms = to_ms_since_boot(get_absolute_time());
continue;
}
/* PERIOD_AVG_P_W per channel: I0 at 0xDC, I1 at 0xC2, I2 at 0xC6. */
float avg_p[3];
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p[0]);
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P1, &avg_p[1]);
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P2, &avg_p[2]);
float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
t_prev_ms = t_now_ms;
for (int ch = 0; ch < 3; ch++) {
double e = (double)avg_p[ch] * dt_s / 3600.0;
total_wh[ch] += e;
printf("[%s] avg_P=%+.1f W E_total=%.3f Wh\n",
CH_NAMES[ch], avg_p[ch], total_wh[ch]);
mqtt_publish_channel(CH_NAMES[ch], avg_p[ch], total_wh[ch]);
}
}
}
Exemple 5 — Bidirectionnel côté maître sur un module BASIC
Objectif : implémenter la comptabilité bidirectionnelle côté maître pendant que le module tourne en firmware BASIC. Le Pico réagit au front descendant DRDY via une IRQ GPIO et sépare consommation / export. Matériel : Pico + rbAmp UI1 ; DRDY relié au GPIO 15.
#include
#include
#include "pico/stdlib.h"
#include "pico/critical_section.h"
#include "hardware/gpio.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
#define PIN_DRDY 15
static volatile bool g_data_ready = false;
/**
* @brief Shared GPIO IRQ callback for the Pico SDK.
* @details The SDK uses a single callback for all GPIO IRQs — we filter by pin.
* Keep the callback short (no I2C, no printf inside an IRQ).
*/
static void gpio_callback(uint gpio, uint32_t events) {
if (gpio == PIN_DRDY && (events & GPIO_IRQ_EDGE_FALL)) {
g_data_ready = true;
}
}
int main(void) {
stdio_init_all();
sleep_ms(2000);
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(RB_ADDR, 2000);
/* DRDY input with internal pull-up; falling-edge IRQ. */
gpio_init(PIN_DRDY);
gpio_set_dir(PIN_DRDY, GPIO_IN);
gpio_pull_up(PIN_DRDY);
gpio_set_irq_enabled_with_callback(PIN_DRDY, GPIO_IRQ_EDGE_FALL,
true, &gpio_callback);
double e_consumed_wh = 0.0;
double e_exported_wh = 0.0;
// Use uint64_t for microsecond counters — to_us_since_boot() returns u64;
// truncating to u32 overflows every ~71.6 minutes and produces a multi-kWh
// dt_s spike on the wrap.
uint64_t t_last_us = to_us_since_boot(get_absolute_time());
uint64_t t_last_print_us = t_last_us;
printf("Bidirectional accumulator started\n");
while (true) {
if (!g_data_ready) {
tight_loop_contents();
continue;
}
g_data_ready = false;
uint32_t t_now_us = to_us_since_boot(get_absolute_time());
/* Signed instantaneous P_real: + consume, − export. */
float p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p);
float dt_s = (float)(t_now_us - t_last_us) / 1000000.0f;
t_last_us = t_now_us;
if (p > 0.0f) e_consumed_wh += (double)p * dt_s / 3600.0;
else e_exported_wh += (double)(-p) * dt_s / 3600.0;
/* Summary print every 5 s — not on every RT window. */
if (t_now_us - t_last_print_us >= 5000000UL) {
t_last_print_us = t_now_us;
printf("P=%+8.1fW consumed=%.4f Wh exported=%.4f Wh net=%+.4f Wh\n",
p, e_consumed_wh, e_exported_wh,
e_consumed_wh - e_exported_wh);
}
}
}
Notes:
gpio_set_irq_enabled_with_callback()du Pico SDK enregistre un rappel partagé pour toutes les IRQ GPIO ; les appels ultérieurs àgpio_set_irq_enabled()le réutilisent.volatile boolsuffit pour une synchronisation par simple drapeau — le RP2040 est à émission unique et le booléen est lu de façon atomique.
Exemple 6 — bilan énergétique de la maison
Objectif : tableau de bord complet du bilan. Trois modules :
- rbAmp n° 1 sur l'alimentation principale (STD — bidirectionnel)
- rbAmp n° 2 sur la sortie de l'onduleur solaire (BASIC OK)
- rbAmp n° 3 UI3 sur trois gros appareils (PAC, climatisation, VE)
Le maître utilise rbamp_io_broadcast_latch() pour des instantanés synchrones et publie un bilan conservé sur MQTT chaque minute.
#include
#include
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "rbamp_io.h"
#define ADDR_MAINS 0x50U
#define ADDR_SOLAR 0x51U
#define ADDR_LOADS 0x52U
#define REG_PERIOD_AVG_P_NEG_MAINS 0xFFU /* set per SKU datasheet on STD */
extern void net_init(void); /* same boilerplate as Ex. 4 */
extern mqtt_client_t *s_mqtt;
typedef struct {
double mains_in_wh;
double mains_out_wh;
double solar_total_wh;
double loads_wh[3];
} totals_t;
int main(void) {
stdio_init_all();
sleep_ms(2000);
net_init();
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(ADDR_MAINS, 2000);
rbamp_io_wait_ready(ADDR_SOLAR, 2000);
rbamp_io_wait_ready(ADDR_LOADS, 2000);
/* Primer snapshot on all modules (general call). GC is opt-in
* (FLEET_CONFIG.bit0, default OFF) — fall back to per-module on NACK. */
uint16_t gc_tick = 0;
if (rbamp_io_broadcast_latch(gc_tick++, 0) != PICO_OK) {
rbamp_io_write_u8(ADDR_MAINS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
rbamp_io_write_u8(ADDR_SOLAR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
rbamp_io_write_u8(ADDR_LOADS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
}
uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
totals_t totals = {0};
printf("Home balance started\n");
while (true) {
sleep_ms(60 * 1000);
/* Synchronous snapshot on all modules. */
if (rbamp_io_broadcast_latch(gc_tick++, 0) != PICO_OK) {
rbamp_io_write_u8(ADDR_MAINS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
rbamp_io_write_u8(ADDR_SOLAR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
rbamp_io_write_u8(ADDR_LOADS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
}
uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
sleep_ms(50);
float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
t_prev_ms = t_now_ms;
/* ----- MAINS (bidirectional, STD) ----- */
uint8_t valid;
if (rbamp_io_read_u8(ADDR_MAINS, RB_REG_PERIOD_VALID, &valid) == PICO_OK
&& (valid & 0x01U)) {
float p_consume = 0.0f, p_export = 0.0f;
rbamp_io_read_float_le(ADDR_MAINS, RB_REG_PERIOD_AVG_P0, &p_consume);
if (REG_PERIOD_AVG_P_NEG_MAINS != 0xFFU) {
rbamp_io_read_float_le(ADDR_MAINS, REG_PERIOD_AVG_P_NEG_MAINS,
&p_export);
}
totals.mains_in_wh += (double)p_consume * dt_s / 3600.0;
totals.mains_out_wh += (double)p_export * dt_s / 3600.0;
}
/* ----- SOLAR (generation only) ----- */
if (rbamp_io_read_u8(ADDR_SOLAR, RB_REG_PERIOD_VALID, &valid) == PICO_OK
&& (valid & 0x01U)) {
float p = 0.0f;
rbamp_io_read_float_le(ADDR_SOLAR, RB_REG_PERIOD_AVG_P0, &p);
totals.solar_total_wh += (double)p * dt_s / 3600.0;
}
/* ----- LOADS (UI3, three channels) ----- */
if (rbamp_io_read_u8(ADDR_LOADS, RB_REG_PERIOD_VALID, &valid) == PICO_OK
&& (valid & 0x01U)) {
float p[3] = {0};
rbamp_io_read_float_le(ADDR_LOADS, RB_REG_PERIOD_AVG_P0, &p[0]); /* I0 */
rbamp_io_read_float_le(ADDR_LOADS, RB_REG_PERIOD_AVG_P1, &p[1]); /* I1 */
rbamp_io_read_float_le(ADDR_LOADS, RB_REG_PERIOD_AVG_P2, &p[2]); /* I2 */
for (int i = 0; i < 3; i++) {
totals.loads_wh[i] += (double)p[i] * dt_s / 3600.0;
}
}
double total_consumed = totals.mains_in_wh + totals.solar_total_wh
- totals.mains_out_wh;
double solar_self_used = totals.solar_total_wh - totals.mains_out_wh;
if (solar_self_used < 0.0) solar_self_used = 0.0;
printf("MAINS in=%.2f out=%.2f\n", totals.mains_in_wh, totals.mains_out_wh);
printf("SOLAR gen=%.2f self-used=%.2f exported=%.2f\n",
totals.solar_total_wh, solar_self_used, totals.mains_out_wh);
printf("LOADS HP=%.2f AC=%.2f EV=%.2f\n",
totals.loads_wh[0], totals.loads_wh[1], totals.loads_wh[2]);
printf("TOTAL household consumed=%.2f Wh\n", total_consumed);
char payload[512];
int n = snprintf(payload, sizeof(payload),
"{\"mains_in\":%.3f,\"mains_out\":%.3f,\"solar\":%.3f,"
"\"self_used\":%.3f,\"total_consumed\":%.3f,"
"\"hp\":%.3f,\"ac\":%.3f,\"ev\":%.3f}",
totals.mains_in_wh, totals.mains_out_wh, totals.solar_total_wh,
solar_self_used, total_consumed,
totals.loads_wh[0], totals.loads_wh[1], totals.loads_wh[2]);
mqtt_publish(s_mqtt, "home/energy/balance", payload, n,
/*qos*/ 1, /*retain*/ 1, NULL, NULL);
}
}
Exemple 7 — détection d'événements de puissance
Objectif : à chaque front DRDY, comparer la puissance instantanée P à une moyenne mobile exponentielle (EMA) et journaliser les écarts significatifs sur une carte SD montée via SPI + FATFS. Matériel : Pico + rbAmp + module carte SD en SPI. Bibliothèque : no-OS-FatFS-SD-SPI-RPi-Pico ou un port FATFS similaire compatible SDK.
#include
#include
#include
#include "pico/stdlib.h"
#include "hardware/gpio.h"
#include "ff.h" /* FATFS API */
#include "rbamp_io.h"
#define RB_ADDR 0x50U
#define PIN_DRDY 15
#define EMA_ALPHA 0.05f
#define EVENT_THRESHOLD_W 200.0f
static volatile bool g_data_ready = false;
static FATFS s_fs;
static FIL s_logfile;
static void gpio_callback(uint gpio, uint32_t events) {
if (gpio == PIN_DRDY && (events & GPIO_IRQ_EDGE_FALL)) {
g_data_ready = true;
}
}
/**
* @brief Mount the SD card and open events.log in append mode.
*/
static bool sd_setup(void) {
if (f_mount(&s_fs, "", 1) != FR_OK) return false;
if (f_open(&s_logfile, "events.log",
FA_OPEN_APPEND | FA_WRITE) != FR_OK) return false;
return true;
}
int main(void) {
stdio_init_all();
sleep_ms(2000);
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(RB_ADDR, 2000);
if (sd_setup()) printf("SD mounted; logging to events.log\n");
else printf("WARN: SD card not available\n");
gpio_init(PIN_DRDY);
gpio_set_dir(PIN_DRDY, GPIO_IN);
gpio_pull_up(PIN_DRDY);
gpio_set_irq_enabled_with_callback(PIN_DRDY, GPIO_IRQ_EDGE_FALL,
true, &gpio_callback);
/* Seed the EMA with current power so we do not log a spurious startup event. */
float p_ema = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p_ema);
printf("Event detector started\n");
while (true) {
if (!g_data_ready) { tight_loop_contents(); continue; }
g_data_ready = false;
float p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p);
float delta = p - p_ema;
p_ema = (1.0f - EMA_ALPHA) * p_ema + EMA_ALPHA * p;
if (fabsf(delta) > EVENT_THRESHOLD_W) {
const char *type = (delta > 0.0f) ? "TURN_ON" : "TURN_OFF";
char line[128];
int n = snprintf(line, sizeof(line),
"%lu %s delta=%+.1f W P=%.1f W EMA=%.1f W\n",
(unsigned long)to_ms_since_boot(get_absolute_time()),
type, delta, p, p_ema);
printf("%s", line);
UINT bw;
f_write(&s_logfile, line, n, &bw);
f_sync(&s_logfile); /* flush to the card */
}
}
}
Exemple 8 — Publieur MQTT avec découverte automatique Home Assistant
Objectif : une intégration HA prête à l'emploi. Le Pico W se connecte au Wi-Fi et à un broker MQTT, publie les configurations HA Auto-discovery (conservées) et émet un état JSON chaque minute. Matériel : Pico W (ou Pico 2 W) + un rbAmp UI1 + Wi-Fi + broker MQTT.
#include
#include
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
#define DEVICE_ID "rbamp_main"
#define DEVICE_NAME "Mains rbAmp"
extern void net_init(void); /* Wi-Fi + MQTT bring-up (Ex. 4) */
extern mqtt_client_t *s_mqtt;
/**
* @brief Publish one HA discovery config (retained).
*/
static void publish_discovery_sensor(const char *key, const char *friendly,
const char *unit, const char *dev_class,
const char *state_class) {
char topic[128], payload[512];
snprintf(topic, sizeof(topic),
"homeassistant/sensor/%s/%s/config", DEVICE_ID, key);
int n = snprintf(payload, sizeof(payload),
"{"
"\"name\":\"%s %s\","
"\"unique_id\":\"%s_%s\","
"\"state_topic\":\"rbamp/%s/state\","
"\"value_template\":\"{{ value_json.%s }}\","
"\"state_class\":\"%s\","
"\"device\":{"
"\"identifiers\":[\"%s\"],"
"\"name\":\"%s\","
"\"manufacturer\":\"rbAmp\","
"\"model\":\"rbAmp UI*\""
"}",
DEVICE_NAME, friendly, DEVICE_ID, key,
DEVICE_ID, key, state_class,
DEVICE_ID, DEVICE_NAME);
if (unit) n += snprintf(payload + n, sizeof(payload) - n,
",\"unit_of_measurement\":\"%s\"", unit);
if (dev_class) n += snprintf(payload + n, sizeof(payload) - n,
",\"device_class\":\"%s\"", dev_class);
n += snprintf(payload + n, sizeof(payload) - n, "}");
mqtt_publish(s_mqtt, topic, payload, n,
/*qos*/ 1, /*retain*/ 1, NULL, NULL);
}
/**
* @brief Publish the full set of HA discovery configs for one rbAmp.
*/
static void publish_discovery_all(void) {
publish_discovery_sensor("voltage", "Voltage", "V", "voltage", "measurement");
publish_discovery_sensor("current", "Current", "A", "current", "measurement");
publish_discovery_sensor("power", "Power", "W", "power", "measurement");
publish_discovery_sensor("energy", "Energy", "Wh", "energy", "total_increasing");
publish_discovery_sensor("frequency", "Frequency", "Hz", "frequency", "measurement");
publish_discovery_sensor("power_factor", "Power Factor", NULL, "power_factor", "measurement");
publish_discovery_sensor("apparent_power", "Apparent Power", "VA", "apparent_power", "measurement");
publish_discovery_sensor("reactive_power", "Reactive Power", "var", "reactive_power", "measurement");
}
/* Set to true by Ex.4's mqtt_conn_cb on MQTT_CONNECT_ACCEPTED.
* (Add `extern volatile bool s_mqtt_connected;` to the net_init translation unit.) */
extern volatile bool s_mqtt_connected;
int main(void) {
stdio_init_all();
sleep_ms(2000);
net_init();
/* MQTT connect is asynchronous — publishing discovery before the CONNECT
* callback fires causes mqtt_publish() to return ERR_CONN and the configs
* to silently disappear. Wait (bounded) for the connection. */
uint32_t mqtt_deadline = to_ms_since_boot(get_absolute_time()) + 15000;
while (!s_mqtt_connected) {
if (to_ms_since_boot(get_absolute_time()) > mqtt_deadline) {
printf("WARN: MQTT not connected after 15 s — discovery will be retried on reconnect\n");
break;
}
sleep_ms(100);
}
if (s_mqtt_connected) publish_discovery_all();
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(RB_ADDR, 2000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD); /* primer */
uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
double total_wh = 0.0;
while (true) {
sleep_ms(60 * 1000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
sleep_ms(50);
uint8_t valid = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
if ((valid & 0x01U) == 0) {
t_prev_ms = to_ms_since_boot(get_absolute_time());
continue;
}
float avg_p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);
float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
total_wh += (double)avg_p * dt_s / 3600.0;
t_prev_ms = t_now_ms;
/* Live RT values for the state payload. */
float u = 0, i_ = 0, pf = 0, q = 0;
uint8_t freq = 0;
rbamp_io_read_float_le(RB_ADDR, RB_REG_U_RMS, &u);
rbamp_io_read_float_le(RB_ADDR, RB_REG_I0_RMS, &i_);
rbamp_io_read_float_le(RB_ADDR, RB_REG_PF0, &pf);
rbamp_io_read_float_le(RB_ADDR, RB_REG_Q0, &q);
rbamp_io_read_u8 (RB_ADDR, RB_REG_AC_FREQ, &freq);
char payload[384];
int n = snprintf(payload, sizeof(payload),
"{"
"\"voltage\":%.1f,"
"\"current\":%.3f,"
"\"power\":%.1f,"
"\"energy\":%.3f,"
"\"frequency\":%u,"
"\"power_factor\":%.3f,"
"\"apparent_power\":%.1f,"
"\"reactive_power\":%.1f"
"}",
u, i_, avg_p, total_wh,
(unsigned)freq, pf, u * i_, q);
mqtt_publish(s_mqtt, "rbamp/" DEVICE_ID "/state", payload, n,
/*qos*/ 0, /*retain*/ 0, NULL, NULL);
printf("Published: %s\n", payload);
}
}
Exemple 9 — Enregistreur sur batterie avec veille dormante
Objectif : un enregistreur extérieur / autonome qui sort du mode dormant toutes les 10 minutes via l'alarme RTC, capture une période, publie via MQTT, puis revient en mode dormant. Le Pico W descend à quelques centaines de µA en sommeil dormant — suffisant pour plusieurs mois sur une cellule Li-ion. Matériel : Pico W + un rbAmp UI1 + Li-ion. Le rbAmp peut être coupé via un interrupteur côté haut sur GPIO 16. Persistance : pico/sleep.h + la RTC intégrée + une petite zone NOINIT (ou une mémoire non volatile externe) pour l'état qui doit survivre au sommeil.
#include
#include
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "pico/sleep.h"
#include "hardware/rtc.h"
#include "hardware/gpio.h"
#include "lwip/apps/mqtt.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
#define PIN_RBAMP_POWER 16
#define WAKE_SECONDS (10 * 60)
extern void net_init(void);
extern mqtt_client_t *s_mqtt;
/* "NOINIT" region — variables that are not zeroed by the startup code.
* They survive dormant sleep on RP2040 because RAM stays powered. */
__attribute__((section(".uninitialized_data")))
static double s_total_wh;
__attribute__((section(".uninitialized_data")))
static uint32_t s_wake_count;
__attribute__((section(".uninitialized_data")))
static bool s_primer_done;
__attribute__((section(".uninitialized_data")))
static uint32_t s_magic; /* 0xCAFEFEED when state is initialised */
/**
* @brief Power-gate the rbAmp module.
*/
static void rbamp_power(bool on) {
gpio_init(PIN_RBAMP_POWER);
gpio_set_dir(PIN_RBAMP_POWER, GPIO_OUT);
gpio_put(PIN_RBAMP_POWER, on);
if (on) sleep_ms(300); /* let the LDO + MCU boot */
}
/**
* @brief Arm the RTC alarm `seconds` ahead (with day-wrap) and enter dormant sleep.
* @details Execution resumes at the reset vector via watchdog. On Pico W,
* deinit CYW43 BEFORE calling this — leaving the radio powered keeps
* the chip at ~10 mA instead of ~180 µA in dormant.
*/
static void enter_dormant(uint32_t seconds) {
datetime_t now;
if (!rtc_get_datetime(&now)) {
/* RTC not running — fall back to a brute reboot via watchdog. */
watchdog_reboot(0, 0, seconds * 1000U);
while (1) tight_loop_contents();
}
/* Convert "now" + `seconds` to absolute calendar time WITH day-wrap.
* Without this, alarms in the last 60 s of a day land at 00:0x today —
* a time in the past — and the RTC never matches until 24 h later. */
int total_sec = now.hour * 3600 + now.min * 60 + now.sec + (int)seconds;
int day_offset = total_sec / 86400;
total_sec %= 86400;
datetime_t alarm = now;
alarm.hour = total_sec / 3600;
alarm.min = (total_sec / 60) % 60;
alarm.sec = total_sec % 60;
if (day_offset > 0) {
/* Bump the day; for periods ≤ 24 h this is at most one day forward. */
alarm.day += day_offset;
/* NOTE: this does not handle month/year roll-over; for periods ≤ 24 h
* and well-set RTC the simplest fix is to step the day field; for a
* production logger use a proper time_t arithmetic via mktime. */
}
sleep_run_from_xosc();
sleep_goto_sleep_until(&alarm, NULL);
/* Force a clean reset so main() re-runs from the top (with NOINIT state). */
watchdog_reboot(0, 0, 1);
while (1) tight_loop_contents();
}
int main(void) {
stdio_init_all();
sleep_ms(1000);
/* Initialise persistent state on cold boot. Write `s_magic` LAST so a
* crash mid-init leaves the marker unset and forces re-initialisation. */
if (s_magic != 0xCAFEFEEDU) {
s_total_wh = 0.0;
s_wake_count = 0;
s_primer_done = false;
__dmb(); /* publish other fields before the marker */
s_magic = 0xCAFEFEEDU;
/* Seed the RTC with an arbitrary epoch so rtc_get_datetime() returns
* a valid struct from the first call. Without this, the alarm math in
* enter_dormant() reads garbage and sleep duration is undefined. */
rtc_init();
datetime_t epoch = { .year=2024, .month=1, .day=1,
.dotw=1, .hour=0, .min=0, .sec=0 };
rtc_set_datetime(&epoch);
sleep_us(64); /* RTC needs a few cycles to latch */
} else {
rtc_init();
}
s_wake_count++;
/* Power up rbAmp + I2C. */
rbamp_power(true);
rbamp_io_init(i2c0, 4, 5, 50000);
if (rbamp_io_wait_ready(RB_ADDR, 2000) != PICO_OK) {
printf("rbAmp not ready — sleeping\n");
rbamp_power(false);
enter_dormant(WAKE_SECONDS);
}
/* First wake-up after a cold boot: primer snapshot only. */
if (!s_primer_done) {
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
s_primer_done = true;
printf("Primer done — entering dormant\n");
rbamp_power(false);
enter_dormant(WAKE_SECONDS);
}
/* Subsequent wake-ups: close the period and read its average power. */
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
sleep_ms(50);
uint8_t valid = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
if ((valid & 0x01U) == 0) {
printf("Stale snapshot — skipping cycle\n");
rbamp_power(false);
enter_dormant(WAKE_SECONDS);
}
float avg_p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);
/* dt approximation: dormant sleep + boot ≈ WAKE_SECONDS. For higher accuracy
* read the RTC calendar on entry and exit. */
float dt_s = (float)WAKE_SECONDS;
s_total_wh += (double)avg_p * dt_s / 3600.0;
/* Publish via Wi-Fi + MQTT (graceful fallback). */
net_init();
if (s_mqtt) {
char payload[256];
int n = snprintf(payload, sizeof(payload),
"{\"wake\":%lu,\"dt_s\":%.1f,\"avg_p\":%.1f,\"energy_wh\":%.3f}",
(unsigned long)s_wake_count, dt_s, avg_p, s_total_wh);
mqtt_publish(s_mqtt, "rbamp/remote/state", payload, n,
/*qos*/ 1, /*retain*/ 1, NULL, NULL);
printf("Published: %s\n", payload);
sleep_ms(200); /* let LwIP flush the publish */
} else {
printf("Wi-Fi/MQTT failed — value buffered in NOINIT RAM\n");
}
/* Power down the CYW43 radio BEFORE dormant — leaving it powered keeps
* the chip at ~10 mA instead of ~180 µA. Required for the headline
* "6 months on a 2000 mAh cell" power budget. */
#if PICO_CYW43_SUPPORTED
cyw43_arch_deinit();
#endif
rbamp_power(false);
enter_dormant(WAKE_SECONDS);
}
Notes:
- La section
.uninitialized_datan'est pas initialisée à zéro au démarrage ; elle survit à la brève réinitialisation qui suit le réveil de veille dormante. Une sentinelle à nombre magique (s_magic) permet de distinguer un démarrage à froid (RAM non initialisée, nombre magique aléatoire) d'un réveil. - Pour une persistance permanente même après le retrait de la batterie, enregistrez périodiquement le total dans la flash interne avec
flash_range_program(). Le SDK Pico contient de bons exemples danspico-examples/flash/. - Un Pico W en veille dormante, avec le CYW43 coupé, reste à environ 1 mA. Le RP2040 seul (Pico) descend à environ 180 µA. Utilisez
cyw43_arch_deinit()avant la mise en veille pour couper l'alimentation du module radio.
Exemple 10 — Tarification selon l'heure (TOU) avec horloge murale SNTP
Objectif : facturer l'énergie selon une grille tarifaire horaire. Le Pico W maintient une horloge murale réelle via SNTP, répartit chaque période close dans le bon compartiment tarifaire, remet à zéro les totaux journaliers à minuit et publie des charges utiles avec horodatages ISO. Matériel : Pico W + un rbAmp UI1 + Wi-Fi.
Ajouts au CMakeLists.txt :
target_link_libraries(example_10
pico_stdlib
hardware_i2c
pico_cyw43_arch_lwip_threadsafe_background
pico_lwip_mqtt
pico_lwip_sntp)
src/example_10.c:
#include
#include
#include
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "lwip/apps/sntp.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
/* CEST = UTC+2. For full DST handling, recompute on roll-over. */
#define TZ_OFFSET_HOURS 2
#define PEAK_START_HOUR 8
#define PEAK_END_HOUR 22
extern void net_init(void);
extern mqtt_client_t *s_mqtt;
typedef struct {
double peak_wh, off_peak_wh;
int day_of_year;
} day_totals_t;
typedef struct {
double peak_wh, off_peak_wh;
} lifetime_totals_t;
static day_totals_t s_today = { .day_of_year = -1 };
static lifetime_totals_t s_lifetime = { 0 };
/**
* @brief Start SNTP and wait until the C library `time(NULL)` returns plausible UTC.
*/
static bool sntp_sync(uint32_t timeout_ms) {
sntp_setoperatingmode(SNTP_OPMODE_POLL);
sntp_setservername(0, "pool.ntp.org");
sntp_setservername(1, "time.google.com");
sntp_init();
absolute_time_t deadline = make_timeout_time_ms(timeout_ms);
while (!time_reached(deadline)) {
time_t now = time(NULL);
if (now > 1700000000) { /* ≥ year 2023 */
struct tm lt;
gmtime_r(&now, <);
printf("SNTP sync: %04d-%02d-%02d %02d:%02d:%02d UTC\n",
lt.tm_year + 1900, lt.tm_mon + 1, lt.tm_mday,
lt.tm_hour, lt.tm_min, lt.tm_sec);
return true;
}
sleep_ms(500);
}
return false;
}
static struct tm local_time(void) {
time_t now = time(NULL) + (TZ_OFFSET_HOURS * 3600);
struct tm lt;
gmtime_r(&now, <);
return lt;
}
static bool is_peak_hour(int hour) {
return (hour >= PEAK_START_HOUR) && (hour < PEAK_END_HOUR);
}
static void iso_now(char *out, size_t out_len) {
struct tm lt = local_time();
char sign = (TZ_OFFSET_HOURS >= 0) ? '+' : '-';
int off = (TZ_OFFSET_HOURS < 0) ? -TZ_OFFSET_HOURS : TZ_OFFSET_HOURS;
snprintf(out, out_len, "%04d-%02d-%02dT%02d:%02d:%02d%c%02d00",
lt.tm_year + 1900, lt.tm_mon + 1, lt.tm_mday,
lt.tm_hour, lt.tm_min, lt.tm_sec, sign, off);
}
/**
* @brief Add one period's energy to the right bucket; roll over the day at midnight.
*/
static void accumulate(double e_wh, const struct tm *tm_now) {
if (s_today.day_of_year != tm_now->tm_yday) {
if (s_today.day_of_year >= 0) {
char payload[192];
int n = snprintf(payload, sizeof(payload),
"{\"yday\":%d,\"peak_wh\":%.3f,\"off_peak_wh\":%.3f,"
"\"total_wh\":%.3f}",
s_today.day_of_year, s_today.peak_wh, s_today.off_peak_wh,
s_today.peak_wh + s_today.off_peak_wh);
mqtt_publish(s_mqtt, "rbamp/tou/day_close", payload, n,
/*qos*/ 1, /*retain*/ 1, NULL, NULL);
printf("Day closed: %s\n", payload);
}
s_today.peak_wh = 0.0;
s_today.off_peak_wh = 0.0;
s_today.day_of_year = tm_now->tm_yday;
}
if (is_peak_hour(tm_now->tm_hour)) {
s_today.peak_wh += e_wh;
s_lifetime.peak_wh += e_wh;
} else {
s_today.off_peak_wh += e_wh;
s_lifetime.off_peak_wh += e_wh;
}
}
int main(void) {
stdio_init_all();
sleep_ms(2000);
net_init();
sntp_sync(15000);
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(RB_ADDR, 2000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD); /* primer */
uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
printf("TOU started: peak %02d:00..%02d:00 local\n",
PEAK_START_HOUR, PEAK_END_HOUR);
while (true) {
sleep_ms(60 * 1000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
sleep_ms(50);
uint8_t valid = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
if ((valid & 0x01U) == 0) {
t_prev_ms = to_ms_since_boot(get_absolute_time());
continue;
}
float avg_p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);
float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
double e_wh = (double)avg_p * dt_s / 3600.0;
t_prev_ms = t_now_ms;
struct tm lt = local_time();
if (lt.tm_year + 1900 < 2023) {
printf("WARN: clock not synced — retrying SNTP\n");
sntp_sync(15000);
continue;
}
accumulate(e_wh, <);
bool peak = is_peak_hour(lt.tm_hour);
char iso[40];
iso_now(iso, sizeof(iso));
char payload[384];
int n = snprintf(payload, sizeof(payload),
"{"
"\"ts\":\"%s\","
"\"tariff\":\"%s\","
"\"avg_p\":%.1f,"
"\"period_wh\":%.4f,"
"\"today_peak_wh\":%.3f,"
"\"today_off_peak_wh\":%.3f,"
"\"life_peak_wh\":%.3f,"
"\"life_off_peak_wh\":%.3f"
"}",
iso, peak ? "peak" : "off_peak",
avg_p, e_wh,
s_today.peak_wh, s_today.off_peak_wh,
s_lifetime.peak_wh, s_lifetime.off_peak_wh);
mqtt_publish(s_mqtt, "rbamp/tou/state", payload, n,
/*qos*/ 0, /*retain*/ 0, NULL, NULL);
printf("%s\n", payload);
}
}
Notes:
pico_lwip_sntpse branche sur le client SNTP de LwIP ; le SDK le relie àtime(NULL)de la bibliothèque C, de sorte quegmtime_r()fonctionne directement.- Pour une gestion complète de l'heure d'été, stockez le décalage UTC dans une petite table, ou intégrez une chaîne TZ POSIX via le mécanisme
tzset()de newlib si votre build le prend en charge. - Pour la mesure bidirectionnelle STD, appelez
accumulate()deux fois — une fois pour la consommation et une fois pour l'export — et publiez les deux compartiments pleines/creuses.
Comparaison des exemples
| # | Complexité | Sortie | MQTT | DRDY | Multi-modules | Bidirectionnel | Persistance | Cas d'usage |
|---|---|---|---|---|---|---|---|---|
| 1 | minimal | USB stdio | — | — | — | — | — | test de fumée |
| 2 | faible | OLED | — | — | — | — | RAM | compteur encapsulé |
| 3 | faible | USB stdio | — | — | oui (3) | — | — | surveillance domestique |
| 4 | moyen | — | oui | — | — | — | RAM | par appareil dans HA |
| 5 | moyen | USB stdio | — | oui | — | oui (maître) | RAM | maison solaire en gamme BASIC |
| 6 | élevé | — | oui | — | oui (3) | oui | RAM | bilan complet du foyer |
| 7 | moyen | USB + SD (FATFS) | — | oui | — | — | Carte SD | détection d'événements |
| 8 | moyen | — | oui (+disco) | — | — | facultatif | RAM + MQTT | Découverte automatique HA |
| 9 | moyen | — | oui | — | — | — | RAM NOINIT | enregistreur hors réseau / extérieur |
| 10 | moyen | USB stdio | oui | — | — | facultatif | RAM + MQTT | Tarification pointe / heures creuses avec SNTP |
Bonnes pratiques
- Vérifiez toujours les codes de retour des appels
rbamp_io_*. Les transactions I²C peuvent échouer sur les longs bus ; le code de production doit réessayer plutôt qu'ignorer l'erreur. - Gardez les callbacks d'IRQ GPIO minimaux. Le SDK Pico utilise un seul callback partagé pour toutes les IRQ GPIO — positionnez un drapeau
volatile boolet revenez. Tout le travail I²C / printf appartient à la boucle principale. - Utilisez
i2c0eti2c1indépendamment. rbAmp suri2c0, OLED suri2c0, carte SD sur SPI — gardez chaque périphérique sur le bus pour lequel il a été initialisé. - Utilisez
to_ms_since_boot(get_absolute_time())pour l'horloge maîtresse. Précision à la microseconde viato_us_since_boot(). Monotone, survit àsleep_ms(). PERIOD_VALID(0x07) doit être vérifié après chaqueCMD_LATCH_PERIOD. Des instantanés périmés apparaissent si le maître interroge plus vite que le firmware n'intègre.- Attendez au moins 50 ms après un instantané avant de lire
0xDC..0xEF. - Pour les configurations multi-modules,
rbamp_io_broadcast_latch(tick, group)via appel général assure une synchronisation précise. La réception GC est sur option par module (FLEET_CONFIG.bit0, par défaut DÉSACTIVÉE). En cas de NACK, revenez à une capture séquentielle module par module. - Pour les applications sur batterie sur Pico W, désinitialisez le CYW43 (
cyw43_arch_deinit()) avant la veille afin de supprimer plusieurs mA. La veille dormante du RP2040 est d'environ 180 µA, celle du RP2350 encore plus basse. - Enregistrez les totaux Wh dans la mémoire flash interne avec
flash_range_program()si vous avez besoin qu'ils survivent à une coupure complète de l'alimentation. La RAM NOINIT survit à la veille dormante mais pas à une coupure d'alimentation. - La prise en charge de
printfflottant est activée par défaut danspico_stdlib. Pour RP2040, l'implémentationpico_floatdu SDK est utilisée ; pour RP2350, la prise en charge FPU matérielle est activée par défaut.
Et ensuite
Après avoir parcouru ces dix exemples :
- Pour le développement ESP32 de style Arduino, voir arduino-examples.md (brut).
- Pour MicroPython / CircuitPython (y compris sur le Pico lui-même), voir micropython-examples.md (brut).
- Pour l'ESP-IDF natif, voir esp-idf-examples.md (brut).
- Pour STM32 HAL, voir stm32-hal-examples.md.
- Pour l'intégration ESPHome (YAML déclaratif), voir
tools/esphome-rbamp/docs/en/. - La spécification formelle des registres I²C utilisée ici se trouve dans api-reference.md.